Buying guide · Intermediate · 3 min read
Multi-Colour and Multi-Material 3D Printing
AMS, CFS, ACE and DIY Feeders
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A multi-colour system feeds several filament spools into one nozzle and swaps colours during a print. Bambu AMS, Creality CFS and Anycubic ACE are the common branded options, with DIY units such as BIQU BMCU for other printers. Expect purge waste at each change, dry filament and a slicer that supports colour mapping. Use compatible filaments and short colour changes where possible.
Key specs at a glance
- Capacity
- Typically 4 spools per unit, with several units chained on some systems
- Colour change
- Filament is unloaded, the new one loaded and the nozzle purged
- Waste
- Purge or prime tower and flush material at each change
- Compatible filaments
- PLA, PETG and similar; flexible or abrasive types need the maker's note
- Slicer
- Must support multi-colour projects and filament mapping
- Drying
- Many units hold spools in a dry environment
System types
Choose a system that suits your printer.
| System | How it works | Notes |
|---|---|---|
| Bambu AMS | Spool feeder with a single path to the toolhead | Works with Bambu printers |
| Creality CFS | Filament system for supported Creality printers | Match the printer model |
| Anycubic ACE / auto-feed | External feeder for Kobra and Photon models | Check printer compatibility |
| DIY (BIQU BMCU etc.) | Open-source feeder kits for other printers | Needs firmware setup |
| Toolchanger / multi-nozzle | Separate hotend per colour | Less waste but costly |
- Bambu AMS
- How it works:
- Spool feeder with a single path to the toolhead
- Notes:
- Works with Bambu printers
- Creality CFS
- How it works:
- Filament system for supported Creality printers
- Notes:
- Match the printer model
- Anycubic ACE / auto-feed
- How it works:
- External feeder for Kobra and Photon models
- Notes:
- Check printer compatibility
- DIY (BIQU BMCU etc.)
- How it works:
- Open-source feeder kits for other printers
- Notes:
- Needs firmware setup
- Toolchanger / multi-nozzle
- How it works:
- Separate hotend per colour
- Notes:
- Less waste but costly
Reducing waste
Every colour swap flushes the nozzle. To cut waste: - Use fewer colour changes by arranging model colours in large areas. - Reduce the flush volume for similar colours (light to dark needs more). - Use a smaller prime tower or print it only when needed. - Combine small multicolour prints in one plate. The filament length calculator helps estimate how much each print uses.
Filament and storage
Stick to PLA, PETG and other types the maker supports. Spools must be a size that fits the holder. Keep them dry: humid filament strings and jams in the feeder. See filament storage. Avoid abrasive or very soft filaments unless the system lists them as compatible.
Setup and tips
- 1Update printer firmware and slicer to the versions the maker lists.
- 2Add the filament types and colours in the slicer, then map each model colour.
- 3Run a small test print with two colours before a large one.
- 4Clean the feeder and the PTFE tubes occasionally.
- 5If you see jams, check spool tension, tube kinks and filament diameter.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Buying a feeder for a different printer model.
- Mapping colours incorrectly in the slicer.
- Using wet filament.
- Underestimating purge waste on small prints.
- Loading soft or abrasive filament not rated for the feeder.
Frequently asked questions
How much waste does multi-colour printing produce?
A lot at first. Reduce changes and flush volumes to save material.
Can I use any spool?
Most standard spools fit, but check diameter and width for the holder.
Do I need AMS for two colours?
You can pause the print and change spools manually for two or three colours.
Which slicer works?
The slicer made for the printer (such as Bambu Studio, Creality Print or Anycubic Slicer) or OrcaSlicer.
Is a toolchanger better?
It wastes less filament but is more complex and expensive.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




