Buying guide · Beginner · 3 min read
Silk, Wood, Matte and Specialty PLA Filaments
What They Are and How to Print Them
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Specialty filaments are mostly PLA with a special finish: silk is glossy and metallic, matte hides layer lines, sparkle and wood add texture, and multicolour spools change hue along the print. They print like PLA but often need a little more heat and less speed. Glow and fibre-filled types wear brass nozzles, so use hardened steel for those.
Key specs at a glance
- Base material
- Mostly PLA, so bed and cooling settings are close to normal PLA
- Silk
- Glossy, metal look, prints best slightly hotter and slower
- Matte
- Low sheen, hides layer lines
- Wood and metal filled
- Particle filled, can clog small nozzles
- Glow in the dark
- Abrasive, use a hardened nozzle
- Multicolour
- Colour changes along the spool or within the strand
The common types
Each one is a style choice. They behave like PLA, with a few quirks.
| Type | Look | Printing notes |
|---|---|---|
| Silk PLA | Glossy, pearly or metallic | Print a little hotter and slower; strings and weaker layer bonding are the usual issues |
| Matte PLA | Flat, soft finish | Prints easily; hides layer lines and small flaws |
| Sparkle / galaxy | Fine glitter effect | Easy; use a 0.4 mm or larger nozzle |
| Wood PLA | Wood-like colour and smell | Contains fine fibre; use a 0.5 mm or larger nozzle and avoid dwelling hot in the nozzle |
| Marble / stone | Speckled grey | Easy; slightly abrasive on some brands |
| Glow in the dark | Charges in light, glows in the dark | Abrasive; use a hardened steel nozzle |
| Multicolour (gradient, rainbow) | Colour shifts along the print | Easy; colour order depends on filament length used |
- Silk PLA
- Look:
- Glossy, pearly or metallic
- Printing notes:
- Print a little hotter and slower; strings and weaker layer bonding are the usual issues
- Matte PLA
- Look:
- Flat, soft finish
- Printing notes:
- Prints easily; hides layer lines and small flaws
- Sparkle / galaxy
- Look:
- Fine glitter effect
- Printing notes:
- Easy; use a 0.4 mm or larger nozzle
- Wood PLA
- Look:
- Wood-like colour and smell
- Printing notes:
- Contains fine fibre; use a 0.5 mm or larger nozzle and avoid dwelling hot in the nozzle
- Marble / stone
- Look:
- Speckled grey
- Printing notes:
- Easy; slightly abrasive on some brands
- Glow in the dark
- Look:
- Charges in light, glows in the dark
- Printing notes:
- Abrasive; use a hardened steel nozzle
- Multicolour (gradient, rainbow)
- Look:
- Colour shifts along the print
- Printing notes:
- Easy; colour order depends on filament length used
Nozzle size and wear
Any filament that contains stone, wood, metal or glow powder rubs the inside of a brass nozzle. A hardened steel or ruby-tipped nozzle lasts much longer and is a cheap upgrade; see nozzles. Use 0.4 mm as the smallest for filled filaments, and 0.6 mm if you see clogging.
Starting point for settings
Use the label first. If it gives only a range, begin near the middle.
+5 to +10 °C over your normal PLA, 30 to 40 mm/s outer walls, a 0.2 mm layer height and good cooling.
same as PLA, perhaps 5 °C cooler to cut sheen variation.
190 to 220 °C, no long pauses at temperature, a wider nozzle if clogs appear.
standard PLA settings, hardened nozzle.
When not to use them
Silk PLA is decorative: layers are weaker than standard PLA, so avoid it for load-bearing parts. Wood filament is brittle in thin sections. For tough parts, use PETG or a tougher PLA grade; see the PLA and PLA+ guide.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using a brass nozzle for glow-in-the-dark filament.
- Printing silk at normal PLA temperature and wondering why it looks dull.
- Using silk for functional parts.
- Letting wood filament sit hot in the nozzle.
- Skipping a test cube when you change brand or colour.
Frequently asked questions
Is silk PLA the same as normal PLA?
It is PLA with additives for a glossy finish. Settings are close, but silk usually wants a bit more heat and less speed, and the layers are weaker.
Does wood filament contain real wood?
It contains fine wood fibre blended into PLA. It looks and smells like wood but is still mostly plastic.
Can I use a 0.4 mm brass nozzle for specialty filament?
For silk and matte, yes. For glow, marble or fibre-filled filaments, use hardened steel.
Why are my multicolour prints not the colour I expected?
The colour depends on how much filament has passed through, so part size and infill change the pattern.
Do specialty filaments need a dry box?
Yes, treat them like PLA and keep them sealed with desiccant. Wet filament makes silk strings and wood bubbles.
Parts for this guide
Search the store for the parts named above, or ask Geeko AI which one fits your project.
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




