How-to · Advanced · 3 min read
Nylon, PC and Carbon Fibre Filaments
PA6-CF, PA6-GF, PAHT-CF and Polycarbonate
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Nylon, polycarbonate and fibre-filled filaments make strong, heat-resistant parts, but they are demanding. Dry the filament first, use a hardened nozzle for carbon (CF) or glass (GF) fills, print in an enclosed printer at high nozzle and bed temperatures and use a suitable build plate or adhesive. Follow the temperatures on the spool.
Key specs at a glance
- Materials
- PA6-CF, PA6-GF, PAHT-CF, PC, ABS-GF
- Nozzle
- Hardened steel for CF and GF
- Nozzle temperature
- High, often 260 to 300 °C; read the spool label
- Bed
- Hot bed with engineering plate or glue
- Environment
- Enclosed, draught-free
- Storage
- Sealed with desiccant
Which material
Pick by what the part needs to do.
| Material | Strengths | Watch out |
|---|---|---|
| PA6-CF (nylon + carbon fibre) | Stiff, light, strong | Very hygroscopic; abrasive |
| PA6-GF (nylon + glass fibre) | Tough, heat resistant | Abrasive; surface is matte |
| PAHT-CF | Higher heat resistance than PA6-CF | Print hot; dry well |
| PC (polycarbonate) | Strong and impact resistant | Warps; needs an enclosure |
| ABS-GF | Stiffer ABS | Fumes; ventilate |
- PA6-CF (nylon + carbon fibre)
- Strengths:
- Stiff, light, strong
- Watch out:
- Very hygroscopic; abrasive
- PA6-GF (nylon + glass fibre)
- Strengths:
- Tough, heat resistant
- Watch out:
- Abrasive; surface is matte
- PAHT-CF
- Strengths:
- Higher heat resistance than PA6-CF
- Watch out:
- Print hot; dry well
- PC (polycarbonate)
- Strengths:
- Strong and impact resistant
- Watch out:
- Warps; needs an enclosure
- ABS-GF
- Strengths:
- Stiffer ABS
- Watch out:
- Fumes; ventilate
Dry it first
Polyamides absorb moisture quickly. Wet filament pops, strings and prints weak parts. Dry nylon and PC in a filament dryer (often around 80 °C for 8 to 12 hours; follow the spool label) and print from a dry box. Store opened spools sealed with desiccant. See filament storage.
Nozzle and hotend
Carbon and glass fibres wear brass nozzles in hours. Use a hardened steel or tungsten-carbide nozzle; see nozzles. Make sure the hotend can reach the temperatures you need and that the PTFE tube is rated for them; see hotend heaters and thermistors.
Printing tips
- 1Use an enclosed printer; see enclosures.
- 2Use an engineering build plate or a thin layer of glue stick for adhesion; see PEI plates.
- 3Print slowly for the first layers and avoid part-cooling fans on PC and nylon unless the profile says so.
- 4Add a brim for PC to resist warping.
- 5Use a profile from the manufacturer as a starting point.
- 6Wear a mask when sanding fibre-filled parts.
Good uses
Gears, brackets, drone parts and jigs from PA6-CF; heat-exposed holders from PAHT-CF and PC; tough clear parts from PC. For softer, flexible parts see TPU, and for standard strong plastics see ABS and ASA.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Printing nylon straight from an open spool.
- Using a brass nozzle with carbon fibre.
- Printing PC in an open frame printer.
- Setting a bed temperature too low for adhesion.
- Sanding without a mask.
Frequently asked questions
Do I need an enclosure?
For PC, yes. For nylon, it helps.
Why is my nylon print weak?
Usually wet filament. Dry it.
Can I print CF filament with a brass nozzle?
Only briefly. Use hardened steel.
What does the GF in PA6-GF mean?
Glass fibre filled.
Is PC food safe?
Printed parts are not generally food safe.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.





