Buying guide · Intermediate · 3 min read
TPU and Flexible Filament
Settings, Hardness and Printer Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
TPU is a rubber-like 3D printing filament used for gaskets, phone cases, tyres and shock pads. Pick the hardness first: 95A is the easiest to print, 85A and softer needs a slow, well-supported feed. Print slowly with little or no retraction, keep the filament dry, and use a direct-drive extruder if you can.
Key specs at a glance
- Hardness
- Quoted in Shore A. 95A is firm and easy, 85A to 90A is softer, below 80A is very soft and hard to feed
- Diameter
- 1.75 mm on most printers
- Nozzle temperature
- Typically 210 to 240 °C, follow the spool label
- Bed
- Typically 30 to 60 °C; PEI or a glue stick helps adhesion
- Speed
- Slow: about 15 to 40 mm/s, lower for softer grades
- Storage
- Dry box, TPU absorbs moisture quickly
What TPU is and when to use it
TPU (thermoplastic polyurethane) is a flexible plastic that stretches and returns to shape. It resists abrasion, oils and impacts far better than PLA, which makes it a good fit for drone camera mounts, bumper corners, wheels, belts, seals and cases.
Related materials sold as TPE or "flexible" filament behave similarly but are often softer and stringier. The rest of this guide uses TPU for both.
Choose the Shore hardness first
Hardness decides how forgiving the material is in the extruder.
| Grade | Feel | Use it for | Printing difficulty |
|---|---|---|---|
| 95A | Firm rubber | Gaskets, bumpers, wheel tyres, cable clips | Easiest; works on many Bowden setups at low speed |
| 90A | Soft rubber | Phone cases, grips, straps | Moderate; direct drive recommended |
| 85A | Very soft | Gaskets, soft feet, wearables | Hard; direct drive and a tight filament path |
| Below 80A | Gel-like | Specialty cushions | Very hard; slow and well supported |
- 95A
- Feel:
- Firm rubber
- Use it for:
- Gaskets, bumpers, wheel tyres, cable clips
- Printing difficulty:
- Easiest; works on many Bowden setups at low speed
- 90A
- Feel:
- Soft rubber
- Use it for:
- Phone cases, grips, straps
- Printing difficulty:
- Moderate; direct drive recommended
- 85A
- Feel:
- Very soft
- Use it for:
- Gaskets, soft feet, wearables
- Printing difficulty:
- Hard; direct drive and a tight filament path
- Below 80A
- Feel:
- Gel-like
- Use it for:
- Specialty cushions
- Printing difficulty:
- Very hard; slow and well supported
Printer setup that helps
puts the extruder right above the hotend, so soft filament has no long tube to buckle in. A Bowden setup can still print firm 95A at low speed.
The filament must not find a gap between the gear and the hotend entry. Printers with a fully enclosed path to the hotend handle soft grades best.
Wet TPU bubbles and strings. See filament storage.
A clean PEI sheet or textured plate holds TPU well; use a thin layer of glue stick if it peels. Do not over-squish the first layer.
Starting settings
Check the spool label first, then start from these values and adjust one at a time.
| Setting | Starting point | Why |
|---|---|---|
| Nozzle | 220 to 230 °C | Hotter flows easier but strings more |
| Bed | 40 to 55 °C | Enough to hold the first layer |
| Speed | 20 to 30 mm/s | Fast pushing compresses the filament and jams |
| Retraction | Off, or 0.5 to 1 mm direct drive | Long retracts pull soft filament out of the gears |
| Cooling fan | 50 to 100 % | Helps bridges and overhangs |
| Flow | Test 95 to 105 % | Soft filament compresses, so check a calibration cube |
- Nozzle
- Starting point:
- 220 to 230 °C
- Why:
- Hotter flows easier but strings more
- Bed
- Starting point:
- 40 to 55 °C
- Why:
- Enough to hold the first layer
- Speed
- Starting point:
- 20 to 30 mm/s
- Why:
- Fast pushing compresses the filament and jams
- Retraction
- Starting point:
- Off, or 0.5 to 1 mm direct drive
- Why:
- Long retracts pull soft filament out of the gears
- Cooling fan
- Starting point:
- 50 to 100 %
- Why:
- Helps bridges and overhangs
- Flow
- Starting point:
- Test 95 to 105 %
- Why:
- Soft filament compresses, so check a calibration cube
Fixing common TPU problems
slow down and close the gap at the extruder; fit a TPU-friendly extruder arm if your printer has one.
dry the spool, then lower the temperature in 5 °C steps.
raise flow slightly and check for a partial clog.
let the bed cool, then flex the plate or use a thin spatula.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Printing TPU at PLA speeds.
- Using long retractions that pull soft filament out of the gears.
- Skipping drying and then blaming the printer for strings.
- Choosing an 85A or softer grade for a first roll on a Bowden printer.
- Over-tightening the extruder spring so the filament is crushed.
Frequently asked questions
Can I print TPU on a Bowden printer?
Often yes with 95A at low speed and a tight filament path, but a direct-drive extruder is much easier.
Is TPU the same as TPE?
No, but they behave alike. TPU is a specific polyurethane; TPE is a wider family of rubber-like plastics. Check the label for hardness.
What does 95A mean?
It is the Shore A hardness. Higher numbers are harder; 95A is firm rubber and the easiest flexible grade to feed.
Do I need a hotter nozzle for TPU?
Slightly hotter than PLA, usually 210 to 240 °C. Follow the spool label and tune by stringing and layer bonding.
How do I store TPU?
In a sealed box with desiccant. TPU takes up moisture fast and prints worse when wet.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Filament manufacturer data sheets (Shore hardness and temperature ranges)
- Slicer documentation for retraction and flow
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



