How-to · Intermediate · 3 min read
Resin Vats, FEP, PFA and ACF Film
Replacing and Tensioning Release Film
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The release film at the bottom of a resin vat peels each cured layer. FEP is the standard, PFA and ACF are tougher and faster. Replace the film when it is cloudy, scratched, dented or leaking, fit it flat with even tension, tighten screws in a cross pattern, and keep the vat clean. Buy film or a tray kit made for your exact printer model.
Key specs at a glance
- Film types
- FEP, nFEP, PFA, ACF
- Sizes
- Cut to match each printer model
- Tension
- Taut like a drum, no wrinkles
- Vat kits
- Complete tray with film pre-fitted
- Lifespan
- Depends on layers printed and resin
- Cleaning
- Isopropyl alcohol and soft wipes
Film types
Choose film for your printer and speed.
| Film | Features | Notes |
|---|---|---|
| FEP | Clear, cheap, standard | Replace often; scratches easily |
| nFEP / textured | Reduces suction | Slightly less transparent |
| PFA | Tougher, better peel | Used on newer printers |
| ACF | Strong multi-layer film | For high-speed printers like Mars 4 Ultra |
| Complete tray / vat kit | Film already fitted | Fastest replacement |
- FEP
- Features:
- Clear, cheap, standard
- Notes:
- Replace often; scratches easily
- nFEP / textured
- Features:
- Reduces suction
- Notes:
- Slightly less transparent
- PFA
- Features:
- Tougher, better peel
- Notes:
- Used on newer printers
- ACF
- Features:
- Strong multi-layer film
- Notes:
- For high-speed printers like Mars 4 Ultra
- Complete tray / vat kit
- Features:
- Film already fitted
- Notes:
- Fastest replacement
When to replace
Replace the film when it is cloudy, has dents or scratches that print through, shows hazy patches where cured resin sticks, or leaks. Poor adhesion on the build plate and failed prints at the same spot are classic signs.
Replacing and tensioning
1. Drain and clean the vat; wear nitrile gloves. 2. Remove the screws and the old film and clean the frame. 3. Lay the new film over the frame with the protective sheet removed. 4. Fit the top frame and tighten the screws gently in a cross pattern so the tension is even. 5. Tap the film: it should sound taut like a drum. 6. Check for wrinkles and leaks, then level and calibrate the printer. See resin printing for the full process.
Care and cleaning
Use plastic scrapers only, never metal. Filter resin back into the bottle after each print and wipe the film with isopropyl alcohol and a soft cloth. Store the vat covered from sunlight. Match your resin with the printer; see standard and water-washable resin and tough, ABS-like and castable resin.
Safety
Uncured resin irritates skin. Wear gloves and eye protection, ventilate the room and wash spills at once. Cure and wash prints in a wash and cure station.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Overtightening one screw and creating wrinkles.
- Using a metal scraper on the film.
- Buying film for the wrong model.
- Printing with a leaking vat.
- Skipping gloves while handling resin.
Frequently asked questions
How often should I change FEP film?
When it becomes cloudy, scratched or leaks. It depends on use.
Is PFA better than FEP?
PFA is usually tougher, so it lasts longer on compatible printers.
How tight should the film be?
Taut like a drum, but not stretched until it deforms.
Can I clean FEP with alcohol?
Yes, with a soft cloth.
Do I need a new vat or just film?
Film is enough unless the frame is damaged.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






