How-to · Beginner · 3 min read
Resin Wash and Cure Stations
IPA, Water Wash, UV Curing Times and Safety
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A wash and cure station cleans uncured resin from prints with isopropyl alcohol (or water for washable resin) and then hardens them under 405 nm UV light. Wash for a few minutes, dry, then cure for the time the resin maker advises. Replace dirty IPA, keep lids closed, wear gloves and never pour resin-contaminated liquid down a drain.
Key specs at a glance
- Machines
- Anycubic Wash & Cure 3 family, Elegoo Mercury, Creality UW-03, HeyGears UltraCraft
- Wash liquid
- IPA 90%+ or water for washable resin
- UV
- 405 nm LEDs with a turntable
- Timers
- Wash 3 to 10 min, cure 2 to 10 min typical
- Volume
- Choose to fit your biggest print plate
- Safety
- Gloves, ventilation, closed lid
Workflow
Follow the same steps for every print.
| Step | What to do | Tip |
|---|---|---|
| 1. Remove from plate | Take the print off the build plate | Wear gloves |
| 2. Wash | Agitate in IPA or water | Do not over-wash; resin can soften |
| 3. Dry | Let it air dry or blow gently | Dry before curing |
| 4. Remove supports | Cut supports when slightly soft or after curing | Depends on the resin |
| 5. Cure | UV for the time on the resin label | Rotate the print |
| 6. Finish | Sand, prime or paint | Wear a mask when sanding |
- 1. Remove from plate
- What to do:
- Take the print off the build plate
- Tip:
- Wear gloves
- 2. Wash
- What to do:
- Agitate in IPA or water
- Tip:
- Do not over-wash; resin can soften
- 3. Dry
- What to do:
- Let it air dry or blow gently
- Tip:
- Dry before curing
- 4. Remove supports
- What to do:
- Cut supports when slightly soft or after curing
- Tip:
- Depends on the resin
- 5. Cure
- What to do:
- UV for the time on the resin label
- Tip:
- Rotate the print
- 6. Finish
- What to do:
- Sand, prime or paint
- Tip:
- Wear a mask when sanding
IPA or water
IPA works with standard resin. Water-washable resin cleans in plain water; see standard and water-washable resin. Replace IPA when it turns cloudy or begins to leave a sticky film; used IPA can be cleared by leaving it in sunlight to cure the resin, then filtering it.
UV curing
Cure under 405 nm light for the time your resin recommends, since under-cured parts stay sticky and over-cured parts become brittle and yellow. Rotate the print or use a turntable so all sides get light. Tough and castable resins have their own times; see tough, ABS-like and castable resin.
Choosing a station
Pick a station that fits your build plate and the largest parts. All-in-one machines wash and cure in one container, while two-box setups let you wash and cure at the same time. Check that the replacement UV lamps and wash baskets are available. Combine with a good FEP film and vat.
Safety and disposal
Wear nitrile gloves and eye protection, work in a ventilated room and keep IPA away from flames. Cure waste resin and used wipes in UV or sunlight before disposal, and follow local waste rules. Never pour liquid resin or contaminated IPA down a drain.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Curing before the print is dry.
- Over-washing in IPA so the print becomes weak.
- Leaving the lid open and filling the room with fumes.
- Pouring used IPA down the sink.
- Using the wrong cure time for the resin.
Frequently asked questions
How long should I wash a print?
Usually 3 to 10 minutes, depending on size and resin.
Can I cure in sunlight?
Yes, but a UV station is faster and more consistent.
When should I change the IPA?
When it becomes cloudy or sticky.
Do I need to remove supports before curing?
Often easier before full cure, but follow the resin guide.
Is IPA flammable?
Yes. Keep it away from flames and sparks.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






