Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsA small wheel with eight compartments sits over the tank; each feeding turns it one-eighth of a turn so one compartment of flakes or pellets drops in. The clock module keeps the times through power cuts. The button gives an extra feed by hand.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
aquarium_fish_feeder_stepper.inoVerify & upload in Electrolark// Aquarium fish feeder with a stepper wheel
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "aquarium-fish-feeder-stepper"
#include <Wire.h>
#include <RTClib.h>
#include <Stepper.h>
// ---- pins ----
const uint8_t ST_IN1 = 2;
const uint8_t ST_IN2 = 3;
const uint8_t ST_IN3 = 4;
const uint8_t ST_IN4 = 5;
const uint8_t BUTTON_PIN = 6;
RTC_DS3231 rtc;
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
const int FEED_TIMES[][2] = {{8, 0}, {18, 0}}; // feeding times (24 h)
const int STEPS_PER_FEED = 256; // 1/8 turn = one compartment of an 8-slot wheel
int lastFedMinute = -1;
void feedOnce() {
stepper.step(STEPS_PER_FEED);
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW);
Serial.println(F("Fed"));
}
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
stepper.setSpeed(10); // rpm (max about 15)
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) { feedOnce(); while (digitalRead(BUTTON_PIN) == LOW) delay(10); } // manual feed
DateTime now = rtc.now();
int m = now.hour() * 60 + now.minute();
for (unsigned int i = 0; i < sizeof(FEED_TIMES) / sizeof(FEED_TIMES[0]); i++) {
if (m == FEED_TIMES[i][0] * 60 + FEED_TIMES[i][1] && lastFedMinute != m) { lastFedMinute = m; feedOnce(); }
}
delay(500);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), DS3231 Precision RTC Module with EEPROM, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (aquarium_fish_feeder_stepper.ino). Install these libraries first: RTClib and Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹519 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pull-ups and debouncing; Real-time clocks and backup batteries; Stepper motors and step sequences.
Ideas that reuse this build: Scheduled pet feeder and Aquarium light scheduler. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.