LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe soil sensor tells the Uno when the pot is dry; a relay then switches the 12 V pump until the soil is damp again. The pump runs from the 12 V adapter, never from the Uno.
Keep the breadboard, relay, battery and USB cable well away from water, and place the water tank beside or below the electronics so a leak or spill cannot run onto them.
Run the pump on the 9 V battery only. Never connect it, or any other part of this project, to mains power.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Powers the pump (a 9 to 12 V rechargeable battery from the lab works too)
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + to the relay COM, relay NO to the pump +, pump - back to the battery -. At 9 V the pump runs a little slower than its 12 V rating. The Uno runs from USB.
atl_auto_plant_waterer.inoVerify & upload in Electrolark// Automatic plant waterer with 12 V pump
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-auto-plant-waterer"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t SOIL_PIN = A0;
const uint8_t RELAY_PIN = 2;
const int SOIL_DRY = 520; // reading in dry air: calibrate
const int SOIL_WET = 260; // reading in a glass of water: calibrate
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
int soilPct = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 35; // water when the soil is drier than this
const float HYSTERESIS = 15; // gap that stops rapid on/off switching
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Soil "));
lcd.print(soilPct);
lcd.print(F("%"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && soilPct < ALERT_LEVEL) alertOn = true;
else if (alertOn && soilPct > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "WATERING" : "Moist";
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
evaluate();
Serial.print(F("Soil="));
Serial.print(soilPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), R385 / R365 Diaphragm Water Pump 12V, 9V Battery, 9V Battery Snap Connector, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (atl_auto_plant_waterer.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹767 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibrating an analog sensor with map(); Character displays and I²C backpacks; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Soil moisture meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Soil=82%, status=Moist
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.