Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsOld brass barometers had a needle that swung from Stormy through Change to Fair. Make your own: paint a half dial from 980 to 1040 hPa, glue a pointer on the servo horn and watch the needle ease left as a storm approaches.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air pressure over I²C.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
barometer_pointer_dial.inoVerify & upload in Electrolark// Old-style barometer pointer dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "barometer-pointer-dial"
#include <Wire.h>
#include <Adafruit_BMP085_U.h>
#include <Servo.h>
// ---- pins ----
const uint8_t SERVO_PIN = 3;
Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085);
Servo servo;
// ---- latest readings ----
float pressHpa = 0;
float bmpC = 0;
const float DIAL_LOW = 980, DIAL_HIGH = 1040; // readings at the two ends of the dial
int pointer = -1;
float bmp180Hpa() { sensors_event_t e; bmp.getEvent(&e); return e.pressure; }
float bmp180C() { float t = 0; bmp.getTemperature(&t); return t; }
void setup() {
Serial.begin(115200);
if (!bmp.begin()) Serial.println(F("BMP180 not found"));
servo.attach(SERVO_PIN);
}
void loop() {
pressHpa = bmp180Hpa();
if (!(true)) { delay(5000); return; }
float frac = constrain((pressHpa - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int angle = 180 - (int)(frac * 180); // low end on the left
if (pointer < 0 || abs(angle - pointer) > 2) { servo.write(angle); pointer = angle; } // ignore tiny wobbles
Serial.print(pressHpa); Serial.print(F(" -> ")); Serial.println(angle);
delay(5000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x77.
That is the sea-level figure. Use the change from your first reading to see height and weather.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), BMP180 Digital Barometric Pressure Sensor Module – I2C Interface, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (barometer_pointer_dial.ino). Install these libraries first: Adafruit BMP085 Unified and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹390 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Barometric pressure and altitude; PWM pulses and servo control.
Ideas that reuse this build: Barometer colour ring and BMP180 pressure and weather watcher. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
1007.81 -> 97
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.