LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsIn a lift the apparent weight rises as it starts upward and falls as it stops. The IMU shows vertical acceleration with its sign (positive speeding up, negative slowing down), so students match each phase of the ride to the data.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Reads vertical acceleration with its sign: positive when speeding up, negative when slowing down, zero at constant speed.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
class_accelerometer_lift.inoVerify & upload in Electrolark// The elevator experiment
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-accelerometer-lift"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float pitchDeg = 0;
float upG = 0;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
const char* statusText = "OK";
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Lift"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Up/down"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(upG, 2);
oled.print(F(" g"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found on the GY-87"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pitchDeg = (readImu(), pitchDegNow());
upG = accEvt.acceleration.z / 9.81f - 1.0f;
Serial.print(F("Up/down="));
Serial.print(upG, 2);
Serial.print(F("g"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA/SCL are not swapped and that VCC_IN (not 3.3V) is used for 5 V boards. Run an I²C scanner: it should show 0x68.
Add a 100 nF capacitor across VCC_IN and GND and keep I²C wires under 20 cm.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Get the school's permission to ride; an adult must supervise.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), GY-87 10DOF Module (MPU6050 + HMC5883L + BMP180), 0.96" OLED Display 128x64 (I2C), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_accelerometer_lift.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,061 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Newton's laws; Acceleration.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g Up/down=0.00g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.