LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe 50 kg load cells sit between two wooden handles. Squeeze as hard as you can and the LCD shows the force in grams (divide by 1000 for kilograms). Compare left and right hands, and see how grip tires after ten squeezes in a row.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Four half-bridge cells under the platform corners share the load, so the scale reads up to 200 kg
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_grip_strength_meter.inoVerify & upload in Electrolark// How strong is your grip?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-grip-strength-meter"
#include <HX711.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float grams = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Weight "));
lcd.print(grams, 0);
lcd.print(F(" g"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
grams = scale.get_units(5);
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Students record the best of three for each hand. Discuss why the dominant hand is stronger and why muscles tire.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HX711 with 4 × 50 kg Half-Bridge Load Cells and Combinator Board, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (class_grip_strength_meter.ino). Install these libraries first: HX711 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹470 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Muscles and force; Fair testing.
Ideas that reuse this build: Weigh it and Hooke's law. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.