LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe spring hangs from the load cell, and the laser sensor below measures the distance to a card on the spring's end. Pull the card down or add weights: the force (grams) and the stretch (fall in millimetres) rise together in a straight line until the spring is overstretched.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
Laser time-of-flight sensor: measures 3 cm to about 1.2 m with millimetre resolution in a tiny package.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_spring_stretch_hookes_law.inoVerify & upload in Electrolark// Stretch a spring: Hooke's law with sensors
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-spring-stretch-hookes-law"
#include <HX711.h>
#include <Wire.h>
#include <Adafruit_VL53L0X.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
Adafruit_VL53L0X tof;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float grams = 0;
int tofMm = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
int readTofMm() {
VL53L0X_RangingMeasurementData_t m;
tof.rangingTest(&m, false);
return (m.RangeStatus != 4) ? m.RangeMilliMeter : -1;
}
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Weight "));
lcd.print(grams, 0);
lcd.print(F(" g"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Rang "));
lcd.print(tofMm);
lcd.print(F(" mm"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
if (!tof.begin()) Serial.println(F("VL53L0X not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
grams = scale.get_units(5);
tofMm = readTofMm();
statusText = (tofMm > 0) ? "OK" : "Sensor error";
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.print(F(", Range="));
Serial.print(tofMm);
Serial.print(F("mm"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Target is out of range or too dark/shiny. Try a white card within 1 m.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Groups record five pairs of readings and plot force against stretch. The slope is the spring constant; a stiffer spring gives a steeper line.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 5kg Load Cell Kit with HX711 Module, VL53L0X ToF Laser Distance Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (class_spring_stretch_hookes_law.ino). Install these libraries first: HX711, Adafruit_VL53L0X and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,042 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Forces and springs; Proportional relationships.
Ideas that reuse this build: Weigh it and Density lab. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
g, Range=398mm Weight=500g, Range=400mm Weight=500g, Range=401mm Weight=500g, Range=401mm Weight=500g, Range=398mm Weight=500g, Range=400mm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.