LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsOn a swing you feel heavier at the bottom and light at the top. The motion sensor reads the force in g and the tilt angle many times a second. Students match the highest reading with the bottom of the swing, and see how it grows with the height of the swing.
Never fix the board to a child. Use a sandbag or a bag of books, and keep everyone clear of the swing path.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Six-axis motion sensor: a three-axis accelerometer that feels gravity and bumps, and a three-axis gyro that measures how fast it turns.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_swing_g_force.inoVerify & upload in Electrolark// How many g on a swing?
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-swing-g-force"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
float gyroZNow() { return gyrEvt.gyro.z * 57.3f; } // turning speed in degrees per second
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Swing"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Pitch: "));
oled.print(pitchDeg, 1);
oled.print(F(" deg"));
oled.setCursor(0, 24);
oled.print(F("Shake: "));
oled.print(shakeG, 2);
oled.print(F(" g"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setGyroRange(MPU6050_RANGE_500_DEG);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
shakeG = shakeGNow();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x68 (0x69 if AD0 is tied high).
Keep I²C wires short, add a 100 nF capacitor across VCC and GND, and mount the board away from motor wires.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Strap the board and a power bank firmly to the seat, not a child. Take readings at three starting heights with a sandbag as the passenger.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-521 MPU6050 6-Axis Gyro and Accelerometer Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_swing_g_force.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹588 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Forces and acceleration; Pendulums.
Never fix the board to a child. Use a sandbag or a bag of books, and keep everyone clear of the swing path.
Ideas that reuse this build: Pendulum period and Accelerometer in a lift. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
deg, Shake=0.00g Pitch=0.0deg, Shake=0.00g Pitch=0.0deg, Shake=0.00g Pitch=0.0deg, Shake=0.00g Pitch=0.0deg, Shake=0.00g Pitch=0.0deg, Shake=0.00g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.