Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsPaint a half-circle dial from 400 to 2000 ppm with the last third in red, and the servo pointer shows the room CO2 in one glance. It looks lovely on the classroom wall and teaches children about ventilation.
A learning and comparison aid, not a certified instrument.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared (NDIR) sensor that measures the real carbon dioxide in the air, from 400 ppm outdoors to 5000 ppm, unlike gas sensors that only guess.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
co2_servo_dial.inoVerify & upload in Electrolark// CO2 pointer dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "co2-servo-dial"
#include <SoftwareSerial.h>
#include <Servo.h>
// ---- pins ----
const uint8_t MHZ_RX = 2;
const uint8_t MHZ_TX = 4;
const uint8_t SERVO_PIN = 3;
SoftwareSerial co2Serial(MHZ_RX, MHZ_TX);
Servo servo;
// ---- latest readings ----
int co2Ppm = 0;
const float DIAL_LOW = 400, DIAL_HIGH = 2000; // readings at the two ends of the dial
int pointer = -1;
int readCo2Ppm() {
const byte cmd[9] = {0xFF, 0x01, 0x86, 0x00, 0x00, 0x00, 0x00, 0x00, 0x79}; // ask for the CO2 reading
byte resp[9];
while (co2Serial.available()) co2Serial.read();
co2Serial.write(cmd, 9);
unsigned long t = millis();
while (co2Serial.available() < 9 && millis() - t < 500) { }
if (co2Serial.available() < 9) return -1;
for (int i = 0; i < 9; i++) resp[i] = co2Serial.read();
if (resp[0] != 0xFF || resp[1] != 0x86) return -1;
return resp[2] * 256 + resp[3];
}
void setup() {
Serial.begin(115200);
co2Serial.begin(9600);
servo.attach(SERVO_PIN);
}
void loop() {
co2Ppm = readCo2Ppm();
if (!(co2Ppm > 0)) { delay(3000); return; }
float frac = constrain((co2Ppm - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int angle = 180 - (int)(frac * 180); // low end on the left
if (pointer < 0 || abs(angle - pointer) > 2) { servo.write(angle); pointer = angle; } // ignore tiny wobbles
Serial.print(co2Ppm); Serial.print(F(" -> ")); Serial.println(angle);
delay(3000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check TX goes to the board RX pin and RX to the board TX pin (crossed), and that it has 5 V.
Wait for the 3 minute warm-up before trusting readings.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Winsen MH-Z19E NDIR CO2 Sensor – UART, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (co2_servo_dial.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹2,196 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
NDIR CO2 sensing and ventilation; PWM pulses and servo control.
A learning and comparison aid, not a certified instrument.
Ideas that reuse this build: CO2 meter and CO2 fresh-air ring. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
650 -> 152
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.