Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsTurn the knob to set anything from 5 seconds to 99 minutes; the step grows as the time gets longer so setting an hour is quick. Press to start or pause, and the buzzer sounds six times at zero. Easier to use than most shop-bought timers.
Tick anything you already have and the total updates.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
countdown_timer_encoder.inoVerify & upload in Electrolark// Kitchen countdown timer with a rotary knob
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "countdown-timer-encoder"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ENC_CLK = 2;
const uint8_t ENC_DT = 3;
const uint8_t ENC_SW = 4;
const uint8_t SEG_CLK = 5;
const uint8_t SEG_DIO = 6;
const uint8_t BUZZER_PIN = 7;
TM1637Display seg(SEG_CLK, SEG_DIO);
int setSeconds = 60;
long remainingMs = 0;
bool running = false;
unsigned long lastTick = 0;
int lastClk = HIGH;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void showTime(long ms) {
int s = (ms + 999) / 1000;
seg.showNumberDecEx((s / 60) * 100 + s % 60, 0b01000000, true);
}
void setup() {
Serial.begin(115200);
pinMode(ENC_CLK, INPUT_PULLUP);
pinMode(ENC_DT, INPUT_PULLUP);
pinMode(ENC_SW, INPUT_PULLUP);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
lastClk = digitalRead(ENC_CLK);
showTime(setSeconds * 1000L);
}
void loop() {
int clk = digitalRead(ENC_CLK);
if (clk != lastClk && clk == LOW) { // one detent
int step = (setSeconds >= 300) ? 60 : (setSeconds >= 60 ? 15 : 5);
if (digitalRead(ENC_DT) != clk) setSeconds += step; else setSeconds -= step;
setSeconds = constrain(setSeconds, 5, 5940);
running = false; showTime(setSeconds * 1000L);
}
lastClk = clk;
if (digitalRead(ENC_SW) == LOW) { // press: start / pause
delay(30);
if (!running) { if (remainingMs <= 0) remainingMs = setSeconds * 1000L; running = true; lastTick = millis(); }
else running = false;
while (digitalRead(ENC_SW) == LOW) delay(5);
}
if (running) {
remainingMs -= (long)(millis() - lastTick); lastTick = millis();
if (remainingMs <= 0) {
remainingMs = 0; running = false; showTime(0);
for (int i = 0; i < 6; i++) { setBuzzer(true); delay(150); setBuzzer(false); delay(150); }
} else showTime(remainingMs);
}
delay(2);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn slower, or add 100 nF capacitors from CLK and DT to GND to debounce.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), KY-040 Incremental Rotary Encoder Module, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (countdown_timer_encoder.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹380 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Multiplexed 7-segment displays; Quadrature encoders.
Ideas that reuse this build: Keypad entry version and Pomodoro focus timer. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.