Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsA lab or exam timer you set by typing. The digits fill the display as you key them, # starts the countdown, * cancels. When it reaches zero the buzzer beeps until you press a key.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
16-key membrane keypad scanned as a 4×4 grid, so 8 wires read 16 buttons.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
keypad_countdown_timer.inoVerify & upload in Electrolark// Keypad countdown timer
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "keypad-countdown-timer"
#include <Keypad.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t KP_R1 = 2;
const uint8_t KP_R2 = 3;
const uint8_t KP_R3 = 4;
const uint8_t KP_R4 = 5;
const uint8_t KP_C1 = 6;
const uint8_t KP_C2 = 7;
const uint8_t KP_C3 = 8;
const uint8_t KP_C4 = 12;
const uint8_t SEG_CLK = 13;
const uint8_t SEG_DIO = 9;
const uint8_t BUZZER_PIN = 10;
const char KEYS[4][4] = {{'1','2','3','A'},{'4','5','6','B'},{'7','8','9','C'},{'*','0','#','D'}};
byte rowPins[4] = {KP_R1, KP_R2, KP_R3, KP_R4};
byte colPins[4] = {KP_C1, KP_C2, KP_C3, KP_C4};
Keypad keypad = Keypad(makeKeymap(KEYS), rowPins, colPins, 4, 4);
TM1637Display seg(SEG_CLK, SEG_DIO);
long entry = 0, remaining = 0;
bool running = false;
unsigned long lastTick = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
seg.showNumberDecEx(0, 0b01000000, true);
}
void loop() {
char k = keypad.getKey();
if (k) {
if (k >= '0' && k <= '9' && !running) { entry = (entry * 10 + (k - '0')) % 10000; seg.showNumberDecEx(entry, 0b01000000, true); }
else if (k == '#') { if (!running && entry > 0) { remaining = (entry / 100) * 60L + entry % 100; running = true; lastTick = millis(); } }
else if (k == '*') { running = false; entry = 0; remaining = 0; seg.showNumberDecEx(0, 0b01000000, true); }
}
if (running && millis() - lastTick >= 1000) {
lastTick += 1000; remaining--;
seg.showNumberDecEx((remaining / 60) * 100 + remaining % 60, 0b01000000, true);
if (remaining <= 0) {
running = false; entry = 0;
for (int i = 0; i < 8; i++) { setBuzzer(true); delay(120); setBuzzer(false); delay(120); }
}
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Rows and columns are swapped or reversed; swap the rowPins and colPins lists.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Membrane Matrix Keypad (4x4), TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (keypad_countdown_timer.ino). Install these libraries first: Keypad and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹453 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Matrix scanning; Multiplexed 7-segment displays.
Ideas that reuse this build: Rotary knob version and Keypad door lock. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.