Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe Pomodoro method splits work into 25-minute sprints with 5-minute breaks. Press the button and the ring lights red, losing one LED every minute and a half; when it empties the buzzer chirps and a green break ring starts. No phone needed, so no distractions.
Tick anything you already have and the total updates.
Sixteen individually addressable RGB LEDs on one data wire.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pomodoro_ring_timer.inoVerify & upload in Electrolark// Pomodoro focus timer with an LED ring
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "pomodoro-ring-timer"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t RING_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
const unsigned long WORK_MS = 25UL * 60 * 1000, BREAK_MS = 5UL * 60 * 1000;
bool working = true, running = false;
unsigned long phaseStart = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void chirp(int n) { for (int i = 0; i < n; i++) { setBuzzer(true); delay(120); setBuzzer(false); delay(120); } }
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
ring.begin();
ring.setBrightness(40);
ring.show();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) {
delay(30);
if (!running) { running = true; working = true; phaseStart = millis(); chirp(1); }
else { running = false; showLevel(0, 0); }
while (digitalRead(BUTTON_PIN) == LOW) delay(5);
}
if (!running) return;
unsigned long len = working ? WORK_MS : BREAK_MS;
unsigned long gone = millis() - phaseStart;
if (gone >= len) { working = !working; phaseStart = millis(); chirp(working ? 1 : 3); return; }
int pct = 100 - (int)(gone * 100UL / len); // ring empties as the time runs out
showLevel(pct, working ? ring.Color(220, 40, 0) : ring.Color(0, 160, 80));
delay(200);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Tactile Push Button Switch, WS2812 RGB LED Ring (16 LEDs), Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (pomodoro_ring_timer.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹368 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Addressable LEDs and colour mixing; Pull-ups and debouncing.
Ideas that reuse this build: Countdown timer and Sunrise alarm. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.