Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA ring beside the study desk shows whether there is enough light for homework: red under about 180 lux, amber under 300 and green above. The child can see at a glance that the lamp should be switched on.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
desk_light_level_ring.inoVerify & upload in Electrolark// Desk light level ring
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "desk-light-level-ring"
#include <Wire.h>
#include <BH1750.h>
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t RING_PIN = 2;
BH1750 lightMeter;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
float lux = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t bandColor(int pct) {
if (pct < 30) return ring.Color(220, 0, 0); // red
if (pct < 50) return ring.Color(200, 120, 0); // amber
return ring.Color(0, 160, 60); // green
}
void setup() {
Serial.begin(115200);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
lux = lightMeter.readLightLevel();
int pct = constrain((int)(constrain((int)(lux / 6), 0, 100)), 0, 100);
showLevel(pct, bandColor(pct));
Serial.print(F("Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), GY-302 BH1750 Light Intensity Module – I2C Interface, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (desk_light_level_ring.ino). Install these libraries first: BH1750 and Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹455 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Lux, lumens and the I²C bus.
Ideas that reuse this build: Study desk lamp checker and Digital lux meter. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Light=320lx Light=321lx Light=319lx Light=320lx Light=320lx Light=320lx Light=321lx Light=319lx Light=320lx
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.