LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA vibration sensor on the inside of the door feels a knock. The LED and a small vibration motor (in a pocket or on a pillow) run for four seconds, so a person who is deaf or wearing headphones knows someone is at the door.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Follow the colours: red is power, dark grey is ground, blue is a signal.
door_knock_light.inoVerify & upload in Electrolark// Door knock light for the hard of hearing
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "door-knock-light"
// ---- pins ----
const uint8_t VIB_PIN = 2;
const uint8_t LED_RED = 3;
const uint8_t VIBE_PIN = 4;
// ---- latest readings ----
bool shake = false;
const unsigned long READ_EVERY_MS = 20;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 4000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void evaluate() {
if (shake) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "KNOCK" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(VIB_PIN, INPUT);
pinMode(LED_RED, OUTPUT);
pinMode(VIBE_PIN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
shake = digitalRead(VIB_PIN) == HIGH;
evaluate();
Serial.print(F("Vibration="));
Serial.print(shake ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRedLed(alertOn);
setVibe(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer and tap harder; loosely mounted modules absorb vibration.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Check the transistor orientation (flat face: C-B-E for BC547).
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), SW-420 Vibration Sensor Module – Digital Output, Through-Hole LED Pack (Pack of 10), Coin Vibration Motor 3V, Resistor Assortment Kit (30 Values), General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (door_knock_light.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹433 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Debouncing noisy digital signals; Transistors as switches.
Ideas that reuse this build: Silent vibration doorbell and Wireless doorbell. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK Vibration=yes, status=KNOCK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.