Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsFine wood and grinding dust is easy to forget about because it does not smell. The GP2Y1010 reads the dust in the air, and above 150 µg/m³ the speaker reminds everyone to wear a mask and switch on the extractor, repeating every ten minutes until the air clears.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Optical dust sensor: an infrared LED shines across a small chamber and a photodiode measures the light scattered by smoke, dust and pollen.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
150 Ω resistor on the LED supply; 1 kΩ in series with the module RX pin
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
dust_voice_warning_workshop.inoVerify & upload in Electrolark// Workshop dust voice warning
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "dust-voice-warning-workshop"
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t DUST_LED = 2;
const uint8_t DUST_PIN = A0;
const uint8_t MP3_RX = 3;
const uint8_t MP3_TX = 4;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DFRobotDFPlayerMini player;
// ---- latest readings ----
float dustUg = 0;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22; // 0-30
const unsigned long QUIET_MS = 600000UL; // at least this long between messages
unsigned long lastPlay = 0;
bool played = false;
float readDustUg() {
float v = 0;
for (int i = 0; i < 10; i++) {
digitalWrite(DUST_LED, LOW); // LED on
delayMicroseconds(280);
v += analogRead(DUST_PIN);
delayMicroseconds(40);
digitalWrite(DUST_LED, HIGH); // LED off
delayMicroseconds(9680);
}
float volts = (v / 10.0f) * VREF / ADC_MAX;
float ug = (volts - 0.6f) * 200.0f; // about 0.5 V per 100 ug/m3 above a 0.6 V clean-air level
return ug < 0 ? 0 : ug;
}
void setup() {
Serial.begin(115200);
pinMode(DUST_LED, OUTPUT);
digitalWrite(DUST_LED, HIGH); // LED off
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
randomSeed(analogRead(A0));
}
void loop() {
dustUg = readDustUg();
if ((dustUg > 150) && (!played || millis() - lastPlay > QUIET_MS)) {
int t = random(1, 3);
player.playMp3Folder(t); // plays /mp3/000t.mp3
played = true; lastPlay = millis();
Serial.print(F("Dusty: track ")); Serial.println(t);
}
delay(100);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dust has settled in the chamber. Blow gently into the air slots and let it settle.
Add the 220 µF capacitor on the LED supply and keep the Vo wire short.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), Sharp GP2Y1010AU0F PM2.5 Dust & Smoke Particle Sensor Module, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Resistor Assortment Kit (30 Values), Electrolytic Capacitor, Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (dust_voice_warning_workshop.ino). Install this library first: DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,295 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Optical scattering and pulsed measurement; Serial-controlled audio playback.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Dusty: track 2
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.