Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA vibration switch on a classroom table or wall shelf trips when it is shaken hard, and the speaker reads out the drill instructions. It is a great way to practise earthquake drills and to learn what a seismometer does, even though it cannot detect a real quake early.
A drill and teaching aid only. It cannot warn of a real earthquake in advance.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
earthquake_shake_voice_alarm.inoVerify & upload in Electrolark// Shake alarm with a spoken drill
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "earthquake-shake-voice-alarm"
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t VIB_PIN = 2;
const uint8_t MP3_RX = 3;
const uint8_t MP3_TX = 4;
DFRobotDFPlayerMini player;
// ---- latest readings ----
bool shake = false;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22; // 0-30
const unsigned long QUIET_MS = 20000UL; // at least this long between messages
unsigned long lastPlay = 0;
bool played = false;
void setup() {
Serial.begin(115200);
pinMode(VIB_PIN, INPUT);
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
randomSeed(analogRead(A0));
}
void loop() {
shake = digitalRead(VIB_PIN) == HIGH;
if ((shake) && (!played || millis() - lastPlay > QUIET_MS)) {
int t = 1;
player.playMp3Folder(t); // plays /mp3/000t.mp3
played = true; lastPlay = millis();
Serial.print(F("Shaking: track ")); Serial.println(t);
}
delay(100);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer and tap harder; loosely mounted modules absorb vibration.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, SW-420 Vibration Sensor Module – Digital Output, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (earthquake_shake_voice_alarm.ino). Install this library first: DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹992 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Debouncing noisy digital signals; Serial-controlled audio playback.
A drill and teaching aid only. It cannot warn of a real earthquake in advance.
Ideas that reuse this build: Vibration alarm and Class vibration table. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Shaking: track 1
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.