LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe flame sensor looks at a model room. When it sees a flame the relay opens the valve to a small sprinkler head and the buzzer sounds. Good for a science fair on fire safety.
A model for a science project only. Never rely on it to protect a real building, and keep water away from the electronics.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Normally-closed 12 V valve: it opens only while the relay powers it
Follow the colours: red is power, dark grey is ground, blue is a signal.
Adapter + to relay COM, relay NO to valve +, valve − to adapter −. The valve sits inline on the water line, after the stop tap.
flame_sprinkler_valve_demo.inoVerify & upload in Electrolark// Flame sprinkler valve demo
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "flame-sprinkler-valve-demo"
// ---- pins ----
const uint8_t FLAME_PIN = 2;
const uint8_t RELAY_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool flame = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 10000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void evaluate() {
if (flame) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "SPRINKLING" : "Standby";
}
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
flame = digitalRead(FLAME_PIN) == LOW;
evaluate();
Serial.print(F("Flame="));
Serial.print(flame ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), Flame Sensor Module – LM393, Digital/Analog Output, 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, 12V Solenoid Water Valve 1/2" (Normally Closed), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (flame_sprinkler_valve_demo.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹858 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Comparator outputs and sensitivity trimmers; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Diya and candle left-burning alarm and Flame watch for a store room. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flame=no, status=Standby Flame=no, status=Standby
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.