LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsWave a hand a few centimetres from the APDS-9960 and the relay switches the lamp on for three seconds, so you can turn a light on with floury, oily or wet hands. Take your hand away and it switches off.
This is a low-voltage bench model. A mains lamp must be switched through a rated contactor installed by an electrician.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared proximity sensor and ambient light sensor in one chip.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Green indicator LED for the normal state.; A bright LED stands in for the lamp in this bench model; a real mains lamp goes through a contactor
Follow the colours: red is power, dark grey is ground, blue is a signal.
For the bench model the relay switches a 12 V lamp or strip from the adapter (COM and NO). A mains street or porch light must be switched by a rated contactor that an electrician installs.
hand_wave_light_switch.inoVerify & upload in Electrolark// Hand-wave light switch
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "hand-wave-light-switch"
#include <Wire.h>
#include <SparkFun_APDS9960.h>
// ---- pins ----
const uint8_t RELAY_PIN = 2;
const uint8_t LED_GREEN = 3;
SparkFun_APDS9960 apds = SparkFun_APDS9960();
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
int proxLevel = 0;
int ambientLevel = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 60; // nearness runs from 0 (far) to 255 (touching); 60 is about 5 cm
const float HYSTERESIS = 15; // gap that stops rapid on/off switching
const unsigned long HOLD_MS = 3000; // keep the alert on this long after the last trigger
unsigned long lastTrigger = 0;
bool levelHigh = false;
int readProx() { uint8_t p = 0; apds.readProximity(p); return p; }
int readAmbient() { uint16_t a = 0; apds.readAmbientLight(a); return a; }
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (!levelHigh && proxLevel > ALERT_LEVEL) levelHigh = true;
else if (levelHigh && proxLevel < ALERT_LEVEL - HYSTERESIS) levelHigh = false;
if (levelHigh) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "LIGHT ON" : "Wave to switch";
}
void setup() {
Serial.begin(115200);
if (!apds.init()) Serial.println(F("APDS-9960 not found"));
apds.enableProximitySensor(false);
apds.enableLightSensor(false);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
proxLevel = readProx();
ambientLevel = readAmbient();
evaluate();
Serial.print(F("Nearness="));
Serial.print(proxLevel);
Serial.print(F(", Light="));
Serial.print(ambientLevel);
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL and that the module is on 3.3 V. An I²C scanner should show 0x39.
Keep the object within about 10 cm and wipe the window.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), APDS9960 RGB Gesture, Proximity and Light Sensor Breakout – I2C, 5V Relay Module with Optocoupler (1 channel), 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (hand_wave_light_switch.ino). Install this library first: SparkFun APDS9960 RGB and Gesture Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹847 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Infrared proximity sensing; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Touch-free hand wave bell and Study room presence light. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch Nearness=0, Light=0, status=Wave to switch
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.