Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsWooden furniture, leather and clothes start to grow mould when the humidity stays above 70 %. This dial shows the room humidity from 30 to 90 %, with the top third marked as the danger zone. Run a dehumidifier or open up the room when the pointer stays there.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
humidity_servo_dial.inoVerify & upload in Electrolark// Monsoon humidity pointer dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "humidity-servo-dial"
#include <DHT.h>
#include <Servo.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t SERVO_PIN = 3;
DHT dht(DHT_PIN, DHT22);
Servo servo;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const float DIAL_LOW = 30, DIAL_HIGH = 90; // readings at the two ends of the dial
int pointer = -1;
void setup() {
Serial.begin(115200);
dht.begin();
servo.attach(SERVO_PIN);
}
void loop() {
humidity = dht.readHumidity();
if (!(!isnan(humidity))) { delay(3000); return; }
float frac = constrain((humidity - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int angle = 180 - (int)(frac * 180); // low end on the left
if (pointer < 0 || abs(angle - pointer) > 2) { servo.write(angle); pointer = angle; } // ignore tiny wobbles
Serial.print(humidity); Serial.print(F(" -> ")); Serial.println(angle);
delay(3000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), DHT22 Temperature & Humidity Sensor, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (humidity_servo_dial.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹486 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
PWM pulses and servo control; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Wardrobe monsoon dehumidifier and Pantry humidity alarm. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
54.81 -> 106
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.