LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe simplest way to understand an inertial sensor: tilt the board and watch the angles on the OLED. Pitch and roll come from the direction of gravity; the shake value is how far the total acceleration is from 1 g. Everything the balancing robots and drones do starts here.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Ten-degree-of-freedom board whose MPU6050 gives acceleration and rotation on three axes; at rest it reads gravity, so it knows how it is tilted.
Follow the colours: red is power, dark grey is ground, blue is a signal.
imu_tilt_readout.inoVerify & upload in Electrolark// Tilt and roll readout with an IMU
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "imu-tilt-readout"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("IMU"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Pitch: "));
oled.print(pitchDeg, 1);
oled.print(F(" deg"));
oled.setCursor(0, 24);
oled.print(F("Roll: "));
oled.print(rollDeg, 1);
oled.print(F(" deg"));
oled.setCursor(0, 34);
oled.print(F("Shake: "));
oled.print(shakeG, 2);
oled.print(F(" g"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found on the GY-87"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
shakeG = shakeGNow();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA/SCL are not swapped and that VCC_IN (not 3.3V) is used for 5 V boards. Run an I²C scanner: it should show 0x68.
Add a 100 nF capacitor across VCC_IN and GND and keep I²C wires under 20 cm.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-87 10DOF Module (MPU6050 + HMC5883L + BMP180), 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (imu_tilt_readout.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹918 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, gyros and tilt angles; Drawing text on an I²C display.
Ideas that reuse this build: Digital spirit level and Gesture-controlled servo. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.