Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsHold the breadboard like a wand: the IMU reads its roll angle and the servo turns to match, smoothed so it does not twitch. It is how gesture-controlled robot arms and camera gimbals start.
Tick anything you already have and the total updates.
Ten-degree-of-freedom board whose MPU6050 gives acceleration and rotation on three axes; at rest it reads gravity, so it knows how it is tilted.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
gesture_wand_servo.inoVerify & upload in Electrolark// Tilt-controlled servo wand
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "gesture-wand-servo"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Servo.h>
// ---- pins ----
const uint8_t SERVO_PIN = 3;
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
Servo servo;
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
float smooth = 90;
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found on the GY-87"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
servo.attach(SERVO_PIN);
}
void loop() {
readImu();
float angle = constrain(rollDegNow() + 90, 0, 180); // tilt the wand left or right
smooth = smooth * 0.8f + angle * 0.2f;
servo.write((int)smooth);
Serial.println((int)smooth);
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA/SCL are not swapped and that VCC_IN (not 3.3V) is used for 5 V boards. Run an I²C scanner: it should show 0x68.
Add a 100 nF capacitor across VCC_IN and GND and keep I²C wires under 20 cm.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-87 10DOF Module (MPU6050 + HMC5883L + BMP180), TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (gesture_wand_servo.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹786 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, gyros and tilt angles; PWM pulses and servo control.
Ideas that reuse this build: Pan-tilt with a joystick and Robotic arm with knobs. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
90 90 90 90 90 90 90 90 90
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.