Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe VL53L1X laser measures the gap to the car from 2 m down to the wall. The ring shows green over 120 cm, amber to 60 cm and red below. Because the beam is narrow it reads the bumper and not the wall behind it.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Laser time-of-flight sensor that measures distance up to about 4 m with millimetre resolution and a narrow beam.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
laser_parking_colour_ring.inoVerify & upload in Electrolark// Laser parking colour ring
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "laser-parking-colour-ring"
#include <Wire.h>
#include <VL53L1X.h>
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t RING_PIN = 2;
VL53L1X tof1;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
float distCm = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t bandColor(int pct) {
if (pct < 30) return ring.Color(220, 0, 0); // red
if (pct < 60) return ring.Color(200, 120, 0); // amber
return ring.Color(0, 160, 60); // green
}
void setup() {
Serial.begin(115200);
Wire.begin();
tof1.setTimeout(500);
if (!tof1.init()) Serial.println(F("VL53L1X not found"));
tof1.setDistanceMode(VL53L1X::Long);
tof1.setMeasurementTimingBudget(50000);
tof1.startContinuous(50);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
distCm = tof1.read() / 10.0f;
int pct = constrain((int)(constrain((int)distCm / 2, 0, 100)), 0, 100);
showLevel(pct, bandColor(pct));
Serial.print(F("Distance="));
Serial.print(distCm, 0);
Serial.print(F("cm"));
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x29.
Aim at a flat, light surface and keep it clear of other objects in the beam.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), TOF400C VL53L1X Laser Ranging Sensor Module – I2C Interface, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (laser_parking_colour_ring.ino). Install these libraries first: VL53L1X and Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹893 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Laser ranging with a narrow beam.
Ideas that reuse this build: Laser parking guide and Distance ring parking aid. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Distance=40cm Distance=40cm Distance=40cm Distance=40cm Distance=40cm Distance=40cm Distance=40cm Distance=40cm Distance=40cm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.