LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsBasic battery chargers and small solar panels keep pushing current into a full battery, boiling off water and shortening its life. The divider watches the battery; at 14.4 V the relay opens the charger line, and it closes again when the battery drops to 13.4 V. The LCD shows the voltage and state.
A 12 V battery can deliver hundreds of amps. Put an inline fuse at the battery terminal and insulate every joint before connecting.
Charge in a ventilated place: charging batteries give off hydrogen. The relay must be rated for the charger current.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Two resistors scale the battery voltage down by 11 so an analog pin can measure up to about 50 V safely.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the board from a 5 V USB charger, or from the 12 V battery through a buck converter set to 5 V. Fuse the battery lead to the divider at 500 mA.
lead_acid_overcharge_cutoff.inoVerify & upload in Electrolark// Lead-acid battery overcharge cut-off
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "lead-acid-overcharge-cutoff"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t VBAT_PIN = A0;
const uint8_t RELAY_PIN = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float batteryV = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 14.4; // 12 V lead-acid batteries are full at 14.4 V; charging further boils off water
const float HYSTERESIS = 1.0; // gap that stops rapid on/off switching
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 11.0f; } // 100 kΩ : 10 kΩ divider = ÷11
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Battery "));
lcd.print(batteryV, 2);
lcd.print(F(" V"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && batteryV > ALERT_LEVEL) alertOn = true;
else if (alertOn && batteryV < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "FULL: charger off" : "Charging";
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
batteryV = readBatteryV();
evaluate();
Serial.print(F("Battery="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRelay(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure the real resistor values and change 11.0 to (R1 + R2) / R2.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Resistor Assortment Kit (30 Values), 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (lead_acid_overcharge_cutoff.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹468 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Isolation, relays and switching higher-power loads; Voltage dividers and ADC scaling.
Ideas that reuse this build: Low-battery load disconnect and Inverter battery monitor. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Battery=16.45V, status=FULL: charger off
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.