Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsA noise dial at the front of the class turns quiet into a game. The sound sensor is read five times a second and the pointer swings across a dial marked Whisper, Talking, Loud and Too loud. Children quickly learn to keep the needle out of the red.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
noise_level_servo_dial.inoVerify & upload in Electrolark// Classroom noise pointer dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "noise-level-servo-dial"
#include <Servo.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t SERVO_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Servo servo;
// ---- latest readings ----
int soundPct = 0;
const float DIAL_LOW = 5, DIAL_HIGH = 80; // readings at the two ends of the dial
int pointer = -1;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void setup() {
Serial.begin(115200);
servo.attach(SERVO_PIN);
}
void loop() {
soundPct = readSoundLevel();
if (!(true)) { delay(200); return; }
float frac = constrain((soundPct - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int angle = 180 - (int)(frac * 180); // low end on the left
if (pointer < 0 || abs(angle - pointer) > 2) { servo.write(angle); pointer = angle; } // ignore tiny wobbles
Serial.print(soundPct); Serial.print(F(" -> ")); Serial.println(angle);
delay(200);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Analog Sound Sensor Microphone Module, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (noise_level_servo_dial.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹461 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
PWM pulses and servo control; Sampling a waveform and measuring amplitude.
Ideas that reuse this build: Classroom noise meter and Noise level logger. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
10 -> 168 10 -> 168 9 -> 171 9 -> 171 9 -> 171 10 -> 168 9 -> 171 9 -> 171 9 -> 171
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.