Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsSmall wall switches are hard to use with arthritis, tremor or limited reach. This puts one large push button wherever it is easy, on a bed rail or wheelchair arm. A quick tap toggles the light; hold it for about a second to toggle the fan. Built here for a 12 V LED lamp and fan.
This bench model switches 12 V loads only. Switching a ceiling fan or room light on mains needs a licensed electrician, rated relays or contactors and a proper enclosure.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Two isolated relays on one board, each switched by its own pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter feeds the fan and your 12 V LED lamp (any 12 V LED bulb or strip under 1 A) through the two relays. Power the Nano from USB or a 5 V phone charger.
one_button_light_and_fan_switch.inoVerify & upload in Electrolark// One big button for the light and fan
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "one-button-light-and-fan-switch"
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t RELAY_1 = 3;
const uint8_t RELAY_2 = 4;
const unsigned long LONG_PRESS_MS = 800; // hold this long to switch the fan instead of the light
bool light = false, fan = false;
void applyRelays() {
digitalWrite(RELAY_1, light ? LOW : HIGH); // active-LOW relay board
digitalWrite(RELAY_2, fan ? LOW : HIGH);
Serial.print(F("Light ")); Serial.print(light ? F("ON") : F("off"));
Serial.print(F(", fan ")); Serial.println(fan ? F("ON") : F("off"));
}
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
pinMode(RELAY_1, OUTPUT);
pinMode(RELAY_2, OUTPUT);
applyRelays();
}
void loop() {
if (digitalRead(BUTTON_PIN) != LOW) return;
unsigned long t0 = millis();
delay(30); // debounce
while (digitalRead(BUTTON_PIN) == LOW && millis() - t0 < LONG_PRESS_MS) delay(5);
if (millis() - t0 >= LONG_PRESS_MS) fan = !fan; // long press: fan
else light = !light; // short tap: light
applyRelays();
while (digitalRead(BUTTON_PIN) == LOW) delay(10); // wait for release
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
7 parts: Nano CH340 Development Board (Soldered), Tactile Push Button Switch, 5V Relay Module with Optocoupler (2 channel), 12V DC Brushless Fan 80mm (cooling fan), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (one_button_light_and_fan_switch.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹721 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; Pull-ups and debouncing.
Ideas that reuse this build: 4-channel room switch panel and IR remote relay switch. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Light off, fan off
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.