LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA reed switch on the lid tells the Uno when the box is opened, and the clock module knows the time. Once it has been opened today, the green light stays on as reassurance. If it is still closed at 9 am, the red light and a short beep every 30 seconds remind whoever is nearby.
A reminder only. It knows the box was opened, not that the medicine was taken.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Glass switch whose contacts close when a magnet is near.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pillbox_not_opened_alarm.inoVerify & upload in Electrolark// Pill box not opened by 9 am alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "pillbox-not-opened-alarm"
#include <Wire.h>
#include <RTClib.h>
// ---- pins ----
const uint8_t REED_PIN = 2;
const uint8_t LED_GREEN = 3;
const uint8_t LED_RED = 4;
const uint8_t BUZZER_PIN = 5;
RTC_DS3231 rtc;
// ---- latest readings ----
bool doorOpen = false;
const int CHECK_H = 9, CHECK_M = 0; // the box should have been opened by this time
bool openedToday = false, wasOpen = false;
int today = -1;
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
DateTime t = rtc.now();
if (t.day() != today) { today = t.day(); openedToday = false; } // a new day starts unopened
doorOpen = digitalRead(REED_PIN) == HIGH;
if (doorOpen && !wasOpen) { openedToday = true; Serial.print(F("Opened at ")); Serial.print(t.hour()); Serial.print(':'); Serial.println(t.minute()); }
wasOpen = doorOpen;
bool late = !openedToday && (t.hour() * 60 + t.minute() >= CHECK_H * 60 + CHECK_M);
setGreenLed(openedToday);
setRedLed(late);
setBuzzer(late && (millis() / 1000) % 30 < 2); // two seconds of beeping every 30 seconds
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Y213 Reed Switch Normally Open (glass), DS3231 Precision RTC Module with EEPROM, 2 × Through-Hole LED Pack (Pack of 10), Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (pillbox_not_opened_alarm.ino). Install this library first: RTClib.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹560 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Pull-up resistors and reed switches; Real-time clocks and backup batteries.
A reminder only. It knows the box was opened, not that the medicine was taken.
Ideas that reuse this build: Medicine voice reminder and Medicine reminder with buzzer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Opened at 9:30
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.