Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA familiar voice works better than a beep. Record a short message for each dose ("Papa, the white tablet after breakfast") and the clock plays it at the set times. The LCD shows the time and the next reminder.
A reminder only. Follow the doctor's instructions and check doses with a pharmacist.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
medicine_voice_reminder.inoVerify & upload in Electrolark// Medicine reminder that speaks
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "medicine-voice-reminder"
#include <Wire.h>
#include <RTClib.h>
#include <DFRobotDFPlayerMini.h>
#include <LiquidCrystal_I2C.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t MP3_RX = 2;
const uint8_t MP3_TX = 3;
RTC_DS3231 rtc;
DFRobotDFPlayerMini player;
LiquidCrystal_I2C lcd(0x27, 16, 2);
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 26;
struct Bell { uint8_t h, m, track; }; // at h:m play /mp3/<track>.mp3
const Bell BELLS[] = {{8, 0, 1}, {14, 0, 2}, {21, 0, 3}};
const int NBELLS = sizeof(BELLS) / sizeof(BELLS[0]);
int lastMinute = -1;
unsigned long lastShow = 0;
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
lcd.init();
lcd.backlight();
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
}
void loop() {
DateTime t = rtc.now();
int m = t.hour() * 60 + t.minute();
if (m != lastMinute) {
lastMinute = m;
for (int i = 0; i < NBELLS; i++)
if (BELLS[i].h == t.hour() && BELLS[i].m == t.minute()) { player.playMp3Folder(BELLS[i].track); Serial.print(F("Reminder ")); Serial.println(BELLS[i].track); }
}
if (millis() - lastShow > 1000) {
lastShow = millis();
char buf[17];
snprintf(buf, sizeof(buf), "%02d:%02d:%02d ", t.hour(), t.minute(), t.second());
lcd.setCursor(0, 0); lcd.print(buf);
int next = -1;
for (int i = 0; i < NBELLS; i++) if (BELLS[i].h * 60 + BELLS[i].m > m) { next = i; break; }
if (next >= 0) snprintf(buf, sizeof(buf), "Next %02d:%02d #%-3d ", BELLS[next].h, BELLS[next].m, BELLS[next].track);
else snprintf(buf, sizeof(buf), "Done for today ");
lcd.setCursor(0, 1); lcd.print(buf);
}
delay(200);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS3231 Precision RTC Module with EEPROM, DFPlayer Mini MP3 Player Module (MP3-TF-16P), LCD1602 16x2 Character LCD (blue, with I2C adapter), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (medicine_voice_reminder.ino). Install these libraries first: RTClib, DFRobotDFPlayerMini and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,184 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Real-time clocks and backup batteries; Serial-controlled audio playback.
A reminder only. Follow the doctor's instructions and check doses with a pharmacist.
Ideas that reuse this build: Medicine reminder with buzzer and Talking clock. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.