Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsAnyone who has lost count of cooker whistles will like this one. The sound sensor sits on the kitchen wall, the sketch counts each whistle (a loud sound lasting longer than 0.7 seconds, so a dropped spoon does not count) and the display shows count:target. When the target is reached the buzzer calls until you press the button.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pressure_cooker_whistle_counter.inoVerify & upload in Electrolark// Pressure cooker whistle counter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "pressure-cooker-whistle-counter"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t BUTTON_PIN = 5;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int soundPct = 0;
const int WHISTLE_LEVEL = 45; // Sound % of a whistle at your distance from the cooker
const unsigned long WHISTLE_MS = 700; // a whistle is a long hiss, not a clang of a spoon
int target = 3; // whistles before the alarm: press the button to change (1 to 9)
int whistles = 0;
unsigned long loudSince = 0;
bool counted = false, alarm = false, wasDown = false;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void show() { seg.showNumberDecEx(whistles * 100 + target, 0b01000000, false); } // "count:target"
void setup() {
Serial.begin(115200);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
show();
}
void loop() {
soundPct = readSoundLevel(); // takes about 50 ms
if (soundPct > WHISTLE_LEVEL) {
if (!loudSince) loudSince = millis();
if (!counted && millis() - loudSince > WHISTLE_MS) {
counted = true; whistles++; show();
Serial.print(F("Whistle ")); Serial.print(whistles); Serial.print(F(" of ")); Serial.println(target);
if (whistles >= target) alarm = true;
}
} else if (soundPct < WHISTLE_LEVEL - 10) { loudSince = 0; counted = false; }
bool down = digitalRead(BUTTON_PIN) == LOW;
if (down && !wasDown) {
if (alarm) { alarm = false; whistles = 0; } // done: switch off the stove and press to reset
else { target = target % 9 + 1; whistles = 0; } // set how many whistles this dish needs
show(); delay(30);
}
wasDown = down;
setBuzzer(alarm && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Raise WHISTLE_LEVEL, or move the sensor closer to the cooker and further from the fan.
Lower WHISTLE_MS to 400 for cookers with a short, sharp whistle.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Analog Sound Sensor Microphone Module, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 11 steps.
No. This page has the complete, tested code (pressure_cooker_whistle_counter.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹445 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Multiplexed 7-segment displays; Pull-ups and debouncing; Sampling a waveform and measuring amplitude.
Ideas that reuse this build: Kitchen timer with a rotary knob and Clap counter for the classroom. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.