LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsEvery year children are forgotten in parked vans and cars, where the heat becomes deadly within minutes. The vibration sensor tells when the engine has been off for two minutes; for the next half hour, any movement seen by the PIR at the back seats sounds the alarm. The driver presses the button after checking the van to clear it.
An extra safeguard only: the driver must always walk to the back and check every seat. A sleeping child may not move enough for the PIR.
Connect through a fuse on a supply that stays on when the ignition is off, and check it does not drain the battery.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Steps the 12 V vehicle supply down to 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Take 12 V from a fused accessory socket or fuse-box tap, through the buck converter set to 5 V, to the board 5V pin. Never connect the board directly to the vehicle 12 V.
school_van_child_left_alarm.inoVerify & upload in Electrolark// Child left in a parked school van alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "school-van-child-left-alarm"
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t VIB_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t BUTTON_PIN = 5;
// ---- latest readings ----
bool motion = false;
bool shake = false;
const unsigned long PARKED_MS = 2 * 60000UL; // no engine vibration this long = vehicle parked
const unsigned long CHECK_MS = 30 * 60000UL; // watch for movement inside for this long after parking
unsigned long lastShake = 0;
bool alarm = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(VIB_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
lastShake = millis();
}
void loop() {
shake = digitalRead(VIB_PIN) == HIGH;
motion = digitalRead(PIR_PIN) == HIGH;
if (shake) lastShake = millis();
unsigned long still = millis() - lastShake;
bool parked = still > PARKED_MS;
if (parked && still < PARKED_MS + CHECK_MS && motion && !alarm) { alarm = true; Serial.println(F("MOVEMENT INSIDE PARKED VEHICLE")); }
if (alarm && digitalRead(BUTTON_PIN) == LOW) { alarm = false; lastShake = millis() - PARKED_MS - CHECK_MS; Serial.println(F("Checked and cleared")); }
setBuzzer(alarm && (millis() / 300) % 2 == 0);
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), HC-SR501 PIR Motion Detector Sensor Module, SW-420 Vibration Sensor Module – Digital Output, Active Buzzer Module 3.3–5V, Tactile Push Button Switch, LM2596 Adjustable Buck Converter Module, PCB Screw Terminal Block 5.08mm (Pack of 5), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (school_van_child_left_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹482 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Debouncing noisy digital signals; Digital inputs and sensor hold time; Pull-ups and debouncing.
An extra safeguard only: the driver must always walk to the back and check every seat. A sleeping child may not move enough for the PIR. Connect through a fuse on a supply that stays on when the ignition is off, and check it does not drain the battery.
Ideas that reuse this build: Car cabin heat alarm and SMS intruder alert. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.