Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe compass module reads the heading and the stepper turns the pointer the other way so it keeps pointing north. Mount it on a card disc with N, E, S and W marked.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three-axis magnetometer: it feels the Earth's magnetic field and works out which way the board is pointing (0 to 359 degrees from north).
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
stepper_compass_pointer.inoVerify & upload in Electrolark// Stepper compass pointer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "stepper-compass-pointer"
#include <Wire.h>
#include <QMC5883LCompass.h>
#include <Stepper.h>
// ---- pins ----
const uint8_t ST_IN1 = 2;
const uint8_t ST_IN2 = 3;
const uint8_t ST_IN3 = 4;
const uint8_t ST_IN4 = 5;
QMC5883LCompass compass;
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
// ---- latest readings ----
int headingDeg = 0;
const int FULL_TURN = 2048; // 28BYJ-48 steps for one turn
int pointerAt = 0; // the pointer starts at North (0 degrees) at power-up
void setup() {
Serial.begin(115200);
compass.init();
stepper.setSpeed(10); // rpm (max about 15)
}
void loop() {
headingDeg = (compass.read(), compass.getAzimuth());
int target = (int)((headingDeg % 360) * (long)FULL_TURN / 360) % FULL_TURN;
int diff = target - pointerAt;
if (diff > FULL_TURN / 2) diff -= FULL_TURN; // always take the short way round
if (diff < -FULL_TURN / 2) diff += FULL_TURN;
if (abs(diff) > 4) { stepper.step(diff); pointerAt = (pointerAt + diff + FULL_TURN) % FULL_TURN; }
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW);
Serial.print(headingDeg); Serial.print(F(" deg -> step ")); Serial.println(pointerAt);
delay(500);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Magnetic north differs from true north by a few degrees in most places. Add or subtract your local declination.
Move the sensor at least 10 cm from motors, magnets and speaker magnets.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-271 QMC5883L 3-Axis Electronic Compass Module – I2C Interface, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (stepper_compass_pointer.ino). Install these libraries first: QMC5883LCompass and Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹560 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Magnetometers and compass headings; Stepper motors and step sequences.
Ideas that reuse this build: Digital compass and Solar panel compass aligner. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
30 deg -> step 170 30 deg -> step 170 30 deg -> step 170 30 deg -> step 170 30 deg -> step 170
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.