Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe waterproof probe sits in a pot and the pointer climbs from 20 to 100 degrees. Great for demonstrating heating curves and checking tea and milk temperatures.
Keep the board and stepper away from steam and splashes; only the probe goes in the pot.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
stepper_kettle_temperature_dial.inoVerify & upload in Electrolark// Stepper kettle temperature dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "stepper-kettle-temperature-dial"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Stepper.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t ST_IN1 = 3;
const uint8_t ST_IN2 = 4;
const uint8_t ST_IN3 = 5;
const uint8_t ST_IN4 = 6;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
// ---- latest readings ----
float probeC = 0;
const float DIAL_LOW = 20, DIAL_HIGH = 100; // readings at the two ends of the dial
const int SWEEP_STEPS = 1365; // pointer travel (2048 steps = one full turn)
int pointerAt = 0; // the pointer starts at the LOW mark at power-up
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setup() {
Serial.begin(115200);
probes.begin();
stepper.setSpeed(10); // rpm (max about 15)
}
void loop() {
probeC = readProbeC();
if (!(probeC > -100)) { delay(1000); return; }
float frac = constrain((probeC - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int target = (int)(frac * SWEEP_STEPS);
if (abs(target - pointerAt) > 4) { stepper.step(target - pointerAt); pointerAt = target; } // ignore tiny wobbles
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW); // coils off: cooler and quieter
Serial.print(probeC); Serial.print(F(" -> step ")); Serial.println(pointerAt);
delay(1000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (stepper_kettle_temperature_dial.ino). Install these libraries first: OneWire, DallasTemperature and Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹470 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Stepper motors and step sequences.
Keep the board and stepper away from steam and splashes; only the probe goes in the pot.
Ideas that reuse this build: Hot water ready voice announcement and Stepper dial thermometer. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
26.00 -> step 102 26.00 -> step 102 26.00 -> step 102
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.