Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe load cell under the pan gives the weight and the pointer shows it on a dial like a mechanical kitchen scale. The pointer moves smoothly, which looks great.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
stepper_kitchen_scale_dial.inoVerify & upload in Electrolark// Stepper kitchen scale dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "stepper-kitchen-scale-dial"
#include <HX711.h>
#include <Stepper.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t ST_IN1 = 4;
const uint8_t ST_IN2 = 5;
const uint8_t ST_IN3 = 6;
const uint8_t ST_IN4 = 7;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
// ---- latest readings ----
float grams = 0;
const float DIAL_LOW = 0, DIAL_HIGH = 1000; // readings at the two ends of the dial
const int SWEEP_STEPS = 1365; // pointer travel (2048 steps = one full turn)
int pointerAt = 0; // the pointer starts at the LOW mark at power-up
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
stepper.setSpeed(10); // rpm (max about 15)
}
void loop() {
grams = scale.get_units(5);
if (!(true)) { delay(500); return; }
float frac = constrain((grams - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int target = (int)(frac * SWEEP_STEPS);
if (abs(target - pointerAt) > 4) { stepper.step(target - pointerAt); pointerAt = target; } // ignore tiny wobbles
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW); // coils off: cooler and quieter
Serial.print(grams); Serial.print(F(" -> step ")); Serial.println(pointerAt);
delay(500);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), 5kg Load Cell Kit with HX711 Module, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (stepper_kitchen_scale_dial.ino). Install these libraries first: HX711 and Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹886 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Stepper motors and step sequences; Strain gauges, amplifiers and calibration factors.
Ideas that reuse this build: Parcel weight limit voice and Luggage weight check scale. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
499.99 -> step 682 499.99 -> step 682
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.