Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsPush the soil fork into a pot and the pointer shows how wet it is, readable from across the room. Paint the right-hand third green, the middle amber and the left red.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
stepper_soil_moisture_dial.inoVerify & upload in Electrolark// Stepper soil moisture dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "stepper-soil-moisture-dial"
#include <Stepper.h>
// ---- pins ----
const uint8_t SOIL_PIN = A0;
const uint8_t ST_IN1 = 2;
const uint8_t ST_IN2 = 3;
const uint8_t ST_IN3 = 4;
const uint8_t ST_IN4 = 5;
const int SOIL_DRY = 520; // reading in dry air: calibrate
const int SOIL_WET = 260; // reading in a glass of water: calibrate
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
// ---- latest readings ----
int soilPct = 0;
const float DIAL_LOW = 0, DIAL_HIGH = 100; // readings at the two ends of the dial
const int SWEEP_STEPS = 1365; // pointer travel (2048 steps = one full turn)
int pointerAt = 0; // the pointer starts at the LOW mark at power-up
void setup() {
Serial.begin(115200);
stepper.setSpeed(10); // rpm (max about 15)
}
void loop() {
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
if (!(true)) { delay(2000); return; }
float frac = constrain((soilPct - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int target = (int)(frac * SWEEP_STEPS);
if (abs(target - pointerAt) > 4) { stepper.step(target - pointerAt); pointerAt = target; } // ignore tiny wobbles
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW); // coils off: cooler and quieter
Serial.print(soilPct); Serial.print(F(" -> step ")); Serial.println(pointerAt);
delay(2000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (stepper_soil_moisture_dial.ino). Install this library first: Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹441 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibrating an analog sensor with map(); Stepper motors and step sequences.
Ideas that reuse this build: Talking plant pot and Soil moisture meter. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
82 -> step 1119
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.