Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsSlots on a disc give pulses and the Nano turns them into rpm, which the servo shows as a needle across a 0 to 3000 dial. It looks like the dials in old cars and is great for a science fair.
Keep fingers and wires clear of spinning parts.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A U-shaped infrared gate: every time a slot in a disc passes through it, the output pulses, so counting pulses gives the speed of a shaft.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
tachometer_servo_dial.inoVerify & upload in Electrolark// Tachometer needle dial
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tachometer-servo-dial"
#include <Servo.h>
// ---- pins ----
const uint8_t SLOT_PIN = 2;
const uint8_t SERVO_PIN = 3;
#ifndef IRAM_SAFE
#define IRAM_SAFE // only needed on ESP32 boards
#endif
volatile unsigned long slotPulses = 0;
unsigned long lastSlotMs = 0;
const int SLOTS_PER_TURN = 20; // holes in the disc on the shaft
Servo servo;
// ---- latest readings ----
float rpm = 0;
const float DIAL_LOW = 0, DIAL_HIGH = 3000; // readings at the two ends of the dial
int pointer = -1;
void IRAM_SAFE onSlotPulse() { slotPulses++; }
float readRpm() {
unsigned long now = millis();
float secs = (now - lastSlotMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = slotPulses;
slotPulses = 0;
interrupts();
lastSlotMs = now;
return (p / secs) * 60.0f / SLOTS_PER_TURN; // turns per minute
}
void setup() {
Serial.begin(115200);
pinMode(SLOT_PIN, INPUT);
attachInterrupt(digitalPinToInterrupt(SLOT_PIN), onSlotPulse, RISING);
lastSlotMs = millis();
servo.attach(SERVO_PIN);
}
void loop() {
rpm = readRpm();
if (!(true)) { delay(500); return; }
float frac = constrain((rpm - DIAL_LOW) / (DIAL_HIGH - DIAL_LOW), 0, 1);
int angle = 180 - (int)(frac * 180); // low end on the left
if (pointer < 0 || abs(angle - pointer) > 2) { servo.write(angle); pointer = angle; } // ignore tiny wobbles
Serial.print(rpm); Serial.print(F(" -> ")); Serial.println(angle);
delay(500);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the disc passes through the gap and that the signal wire is on an interrupt pin (D2 or D3 on a Nano).
Count the slots again and set SLOTS_PER_TURN to the right number.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Groove Coupler Speed Measuring Sensor Module, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (tachometer_servo_dial.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹402 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Counting pulses with interrupts; PWM pulses and servo control.
Keep fingers and wires clear of spinning parts.
Ideas that reuse this build: DIY tachometer and Fan speed checker. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0.00 -> 180 0.00 -> 180 0.00 -> 180 0.00 -> 180 0.00 -> 180 0.00 -> 180
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.