Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA flow sensor in the tap line measures litres per minute and the ring glows green below 5, amber to 8 and red above that. Children quickly learn to run the tap gently while brushing teeth or washing vegetables. A fine way to teach water saving.
Use a food-safe flow sensor for drinking water, with plumbing fittings sealed against leaks. Keep the board and ring dry.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
tap_flow_ring.inoVerify & upload in Electrolark// Water flow colour ring for the kitchen tap
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tap-flow-ring"
#include <Adafruit_NeoPixel.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
const uint8_t RING_PIN = 3;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t bandColor(int pct) {
if (pct < 50) return ring.Color(0, 160, 60); // green
if (pct < 80) return ring.Color(200, 120, 0); // amber
return ring.Color(220, 0, 0); // red
}
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
flowLpm = readFlowLpm();
litres = litresTotal;
int pct = constrain((int)(flowLpm * 10), 0, 100);
showLevel(pct, bandColor(pct));
Serial.print(F("Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.print(F(", Total="));
Serial.print(litres, 2);
Serial.print(F("L"));
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), YF-S201 Water Flow Sensor 1–30 L/min, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (tap_flow_ring.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹521 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Interrupts and counting pulses.
Use a food-safe flow sensor for drinking water, with plumbing fittings sealed against leaks. Keep the board and ring dry.
Ideas that reuse this build: Water flow meter and Water budget. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flow=0.0L/min, Total=0.00L Flow=0.0L/min, Total=0.00L
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.