Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsTouchless taps save water and stop germs passing between hands on the handle, which matters in clinics, school washrooms and kitchens. The ultrasonic sensor beside the spout sees hands; the relay opens a solenoid valve in the supply pipe, and closes it 1.5 seconds after the hands move away.
Keep the board and adapter in a sealed box away from the basin. Use a valve rated for your water pressure, and keep the normal tap upstream so you can shut it off.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Normally-closed 12 V valve in the tap supply: it opens only while the relay powers it
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter powers the solenoid valve through the relay contacts. Power the Nano from a 5 V USB charger, kept well away from water splashes.
touchless_water_tap.inoVerify & upload in Electrolark// Touchless water tap for washbasins
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "touchless-water-tap"
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 3;
const uint8_t RELAY_PIN = 4;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float distCm = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 12; // hands under the spout come within about 10 cm of a sensor beside it
const float HYSTERESIS = 4; // gap that stops rapid on/off switching
const unsigned long HOLD_MS = 1500; // keep the alert on this long after the last trigger
unsigned long lastTrigger = 0;
bool levelHigh = false;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void evaluate() {
if (!(distCm > 0)) { statusText = "Sensor error"; return; }
if (!levelHigh && distCm < ALERT_LEVEL) levelHigh = true;
else if (levelHigh && distCm > ALERT_LEVEL + HYSTERESIS) levelHigh = false;
if (levelHigh) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "Water on" : "Off";
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
distCm = readDistanceCm();
evaluate();
Serial.print(F("Distance="));
Serial.print(distCm, 0);
Serial.print(F("cm"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
7 parts: Nano CH340 Development Board (Soldered), HC-SR04 Ultrasonic Range Finder Sensor Module, 5V Relay Module with Optocoupler (1 channel), 12V Solenoid Water Valve 1/2" (Normally Closed), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (touchless_water_tap.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹863 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; Time-of-flight measurement with sound.
Ideas that reuse this build: Touchless sanitiser dispenser and Handwash timer. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off Distance=60cm, status=Off
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.