Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA PIR under the bed frame sees your feet and the LDR checks that the room is dark. The strip fades up to a soft warm glow, stays on for 45 seconds after you stop moving and then fades slowly out. Amber light does not dazzle eyes that have adjusted to the dark.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Addressable RGB LED strip: cut to length (here 30 LEDs, half a metre) and control every LED individually from one data pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
under_bed_night_light.inoVerify & upload in Electrolark// Under-bed motion night light
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "under-bed-night-light"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t LDR_PIN = 3;
const uint8_t RING_PIN = 4;
const int RING_LEDS = 30;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
bool motion = false;
bool dark = false;
const unsigned long ON_MS = 45000UL; // night walk: stays on this long after the trigger ends
const int MAX_LEVEL = 140; // brightness, 0-255 (a soft glow, not a floodlight)
unsigned long lastTrigger = 0;
int level = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void paint() {
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, ring.Color(level, level * 3 / 5, level / 4));
ring.show();
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(LDR_PIN, INPUT);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
motion = digitalRead(PIR_PIN) == HIGH;
dark = digitalRead(LDR_PIN) == HIGH;
if (motion && dark) lastTrigger = millis();
int target = (lastTrigger && millis() - lastTrigger < ON_MS) ? MAX_LEVEL : 0;
if (level < target) level += 5; else if (level > target) level -= 2; // quick fade in, slow fade out
level = constrain(level, 0, MAX_LEVEL);
paint();
delay(15);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Some modules invert DO. Change == HIGH to == LOW in the code.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), HC-SR501 PIR Motion Detector Sensor Module, Digital LDR Light Sensor Module – LM393, WS2812B Addressable RGB LED Strip (60 LEDs/m), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (under_bed_night_light.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹867 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Digital inputs and sensor hold time; Thresholds set in hardware vs software.
Ideas that reuse this build: Wardrobe light and Staircase lights. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.