Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA PIR at the top and one at the bottom tell the Uno which way you are going. After dark, the LED strip lights one LED at a time in your direction, stays on for 25 seconds after the last movement, and then switches off in the same direction.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sees someone arriving at the foot of the stairs.; Sees someone arriving at the top of the stairs.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Addressable RGB LED strip: cut to length (here 30 LEDs, half a metre) and control every LED individually from one data pin.
Or a 5 V 2 A adapter: the strip needs its own supply
Follow the colours: red is power, dark grey is ground, blue is a signal.
stair_led_sweep.inoVerify & upload in Electrolark// Staircase lights that follow you
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "stair-led-sweep"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t PIR_BOTTOM = 2;
const uint8_t PIR_TOP = 3;
const uint8_t LDR_PIN = 4;
const uint8_t RING_PIN = 5;
const int RING_LEDS = 30;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
bool motionBottom = false;
bool motionTop = false;
bool dark = false;
const unsigned long ON_MS = 25000; // stays lit this long after the last person is seen
const int STEP_MS = 40; // delay between LEDs as the light runs up or down the stairs
unsigned long lastSeen = 0;
bool lit = false;
int dir = 1; // 1 = sweep from the bottom, -1 = from the top
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void sweep(bool turnOn, int direction) {
for (int k = 0; k < RING_LEDS; k++) {
int i = direction > 0 ? k : RING_LEDS - 1 - k;
ring.setPixelColor(i, turnOn ? ring.Color(255, 170, 90) : 0); // warm white
ring.show();
delay(STEP_MS);
}
}
void setup() {
Serial.begin(115200);
pinMode(PIR_BOTTOM, INPUT);
pinMode(PIR_TOP, INPUT);
pinMode(LDR_PIN, INPUT);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
bool bottom = digitalRead(PIR_BOTTOM) == HIGH, top = digitalRead(PIR_TOP) == HIGH;
bool dark = digitalRead(LDR_PIN) == HIGH;
if ((bottom || top) && (dark || lit)) {
if (!lit) { dir = bottom ? 1 : -1; sweep(true, dir); lit = true; Serial.println(bottom ? F("Up from the bottom") : F("Down from the top")); }
lastSeen = millis();
}
if (lit && millis() - lastSeen > ON_MS) { sweep(false, dir); lit = false; } // switches off in the direction of travel
delay(20);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Some modules invert DO. Change == HIGH to == LOW in the code.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 2 × HC-SR501 PIR Motion Detector Sensor Module, Digital LDR Light Sensor Module – LM393, WS2812B Addressable RGB LED Strip (60 LEDs/m), Resistor Assortment Kit (30 Values), Enclosed SMPS Power Supply (12V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (stair_led_sweep.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,256 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Digital inputs and sensor hold time; Thresholds set in hardware vs software.
Ideas that reuse this build: Under-bed night light and Automatic dusk-to-dawn light. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.