GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsRunning an engine in a small closed garage fills it with carbon monoxide. The MQ-7 and DHT22 report the CO level and temperature to a phone page, and it flags when the level rises, so family can keep out of the area.
A learning aid, not a certified CO detector. Never run an engine in a closed garage.
Tick anything you already have and the total updates.
Heated sensor that responds to carbon monoxide (CO), the silent gas from charcoal, generators and blocked chimneys.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
wifi_car_garage_co_and_temperature.inoVerify & upload in Electrolark// Wi-Fi garage CO and temperature monitor
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-car-garage-co-and-temperature"
#include <DHT.h>
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t CO_PIN = 0;
const uint8_t DHT_PIN = 10;
const int ADC_MAX = 4095; // 12-bit analog input
const float VREF = 3.3f;
DHT dht(DHT_PIN, DHT22);
// ---- latest readings ----
int coPct = 0;
float tempC = 0;
float humidity = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
bool alertOn = false;
const float ALERT_LEVEL = 30; // adjust to suit
const float HYSTERESIS = 8;
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Garage</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Garage</h1><div class="g" id="g"></div><p class="s" id="s">Connecting…</p>
<script>const F=[["coPct","CO","%"],["tempC","Temp","C"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
setInterval(tick,2000);tick();</script></body></html>)HTML";
void handleData() {
String j = "{";
j += "\"coPct\":"; j += String(coPct); j += ",";
j += "\"tempC\":"; j += String(tempC, 1); j += ",";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void evaluate() {
if (millis() < 60000UL) { statusText = "Warming up"; return; }
if (!(!isnan(tempC) && !isnan(humidity))) { statusText = "Sensor error"; return; }
if (!alertOn && coPct > ALERT_LEVEL) alertOn = true;
else if (alertOn && coPct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "CO RISK" : "OK";
}
void setup() {
Serial.begin(115200);
dht.begin();
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
coPct = (int)(analogRead(CO_PIN) * 100L / ADC_MAX);
tempC = dht.readTemperature();
humidity = dht.readHumidity();
evaluate();
Serial.print(F("CO="));
Serial.print(coPct);
Serial.print(F("%"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
6 parts: ESP32-C3 SuperMini Development Board, MQ-7 CO Carbon Monoxide Gas Sensor Module – Analog & Digital Output, DHT22 Temperature & Humidity Sensor, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (wifi_car_garage_co_and_temperature.ino). Install these libraries first: DHT sensor library and Adafruit Unified Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹614 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Single-wire digital sensors and why some sensors need slow polling.
A learning aid, not a certified CO detector. Never run an engine in a closed garage.
Ideas that reuse this build: Garage CO monitor and Wi-Fi CO monitor. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 CO=29%, Temp=26.9C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.