GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsThe divider scales the 12 V battery for the ESP32-C3 analog pin, and the page shows the voltage with "Low" below 11.8 V. Your router must be on the inverter or a UPS for the page to stay reachable during a cut.
Tick anything you already have and the total updates.
Two resistors scale the battery voltage down by 11 so an analog pin can measure up to about 50 V safely.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the ESP32-C3 from a 5 V USB charger on the inverter output, or from the battery through a buck converter set to 5 V. Fuse the battery lead to the divider.
wifi_inverter_battery.inoVerify & upload in Electrolark// Wi-Fi inverter battery monitor
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-inverter-battery"
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t VBAT_PIN = 0;
const int ADC_MAX = 4095; // 12-bit analog input
const float VREF = 3.3f;
// ---- latest readings ----
float batteryV = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
bool alertOn = false;
const float ALERT_LEVEL = 11.8; // adjust to suit
const float HYSTERESIS = 0.4;
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Inverter</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Inverter</h1><div class="g" id="g"></div><p class="s" id="s">Connecting…</p>
<script>const F=[["batteryV","Battery","V"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
setInterval(tick,2000);tick();</script></body></html>)HTML";
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 11.0f; } // 100 kΩ : 10 kΩ divider = ÷11
void handleData() {
String j = "{";
j += "\"batteryV\":"; j += String(batteryV, 2); j += ",";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void evaluate() {
if (!alertOn && batteryV < ALERT_LEVEL) alertOn = true;
else if (alertOn && batteryV > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Low: save power" : "Battery OK";
}
void setup() {
Serial.begin(115200);
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
batteryV = readBatteryV();
evaluate();
Serial.print(F("Battery="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure the real resistor values and change 11.0 to (R1 + R2) / R2.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
4 parts: ESP32-C3 SuperMini Development Board, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 6 steps.
No. This page has the complete, tested code (wifi_inverter_battery.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹369 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Voltage dividers and ADC scaling.
Ideas that reuse this build: Offline version. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Battery=10.89V
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.