How-to · Advanced · 3 min read
Building Li-ion Battery Packs
Spot Welding and Safety
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A Li-ion pack is cells joined in series for voltage and in parallel for capacity, for example 3S2P gives 11.1 V nominal and twice the capacity of one cell. Use identical, matched cells, join them with pure nickel strip using a spot welder rather than a soldering iron, insulate every positive end, and fit a BMS rated for your current plus a fuse. Mistakes can cause fires, so work slowly.
Key specs at a glance
- Series (S)
- Adds voltage: 3.7 V nominal per cell, 4.2 V full
- Parallel (P)
- Adds capacity and current
- Cell matching
- Same model and batch; voltages within about 0.05 V before joining in parallel
- Interconnect
- Pure nickel strip, spot welded
- Protection
- BMS for the cell count, fuse, insulating fish-paper rings
- Holders
- Plastic spacers keep cells apart and aligned
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Plan the pack
Decide voltage first: 2S for 7.4 V robots, 3S for 11.1 V, 4S for 14.8 V. Then capacity and current: each parallel group multiplies both. Example: 3S2P with 2500 mAh cells rated 10 A gives 11.1 V, 5000 mAh and about 20 A. Choose a BMS with the same cell count and a continuous rating above your load, and size the nickel strip for the current: one layer of thin strip suits a few amps; high-current packs need wider strip or more layers.
Build steps
- 1Check every cell's voltage and, ideally, capacity. Reject any with damaged wrappers or dents.
- 2Fit the cells into spacer holders, positives and negatives in the right pattern.
- 3Spot weld nickel strip, two or more welds per contact. Practise on a scrap cell first.
- 4Never solder directly to cells: the heat damages the seal and the cell.
- 5Add fish-paper rings on positive ends and insulate between strips.
- 6Connect the BMS balance wires in order, starting from B−, then the main leads.
- 7Add a fuse on the main lead, wrap the pack and add strain relief.
Build on a non-conductive surface, remove rings and watches, keep metal tools insulated, and keep a bucket of sand nearby.
Choosing a spot welder
Handheld battery-powered spot welding pens are fine for small packs with 0.1 to 0.15 mm strip. Capacitor or transformer welders give more consistent welds for thicker strip. Good welds should tear the strip, not peel off cleanly, when tested. Pure nickel has lower resistance than nickel-plated steel, which runs hot at higher currents.
Try it: Battery pack calculator
Change the values and the diagram and results update as you type.
Build a 3S Li-ion pack with a BMS
You need: Three matched 18650 cells, Cell spacers, Pure nickel strip, 3S BMS board, Fish-paper rings, Fuse and holder, Heat shrink wrap · Tools: Spot welder, Multimeter, Insulated tweezers
Get the parts5 of 7 found in our store · ₹461
- Three matched 18650 cellsFind this part
- Cell spacersFind this part
Pure nickel stripPure Nickel Strip for Battery Spot Welding₹350
3S BMS boardLi-ion BMS Protection Board₹49
Fish-paper ringsBarley Fish Paper with Adhesive (1 Metre)₹25Closest match, check the specs- Fuse and holderInline Blade Fuse Holder (Car Type)₹24
Heat shrink wrapHeat Shrink Tubing₹13Closest match, check the specs
- 1Match cellsMeasure and match the cells' voltages.
- 2ArrangePlace the cells in spacers in series orientation.
- 3WeldSpot weld nickel strip between cells with several welds per joint.
- 4Fit BMSSolder balance wires to the BMS in order from B−, then fit main leads.
- 5ProtectAdd fuse, insulation and wrap, then test voltage and a charge cycle.
Common mistakes to avoid
- Soldering directly to cell ends.
- Joining cells in parallel at different voltages.
- Using nickel-plated steel strip for high current.
- Wiring BMS balance leads out of order.
- Skipping fish paper on positive ends.
Frequently asked questions
Can I solder 18650 cells?
It is not recommended. The heat can damage the cell's internal seal; spot welding is safer and more reliable.
What does 3S2P mean?
Three groups in series, each with two cells in parallel: 11.1 V nominal and twice the capacity of one cell.
Do I need a BMS?
Yes for any multi-cell Li-ion pack without an external balance charger and protection.
Can I mix old and new cells?
No. Mismatched cells age differently and the weakest cell gets over-discharged.
Pure nickel or nickel-plated strip?
Pure nickel conducts better and stays cooler; use it for anything above a few amps.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


