LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsHome workers who make agarbatti count thousands of sticks by hand. The infrared sensor counts each stick as it slides off the conveyor. At 25 the relay stops the belt and beeps three times; tie the bundle and press the button for the next one. Change TARGET for bundles of 20 or 50.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Two infrared reflectance sensors: black tape reflects little IR, white floor reflects a lot, so each output tells you which side the line is on.
Bright 4-digit 7-segment display driven by two wires.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
agarbatti_bundle_counter.inoVerify & upload in Electrolark// Incense stick bundle counter
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "agarbatti-bundle-counter"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t LINE_LEFT = 2;
const uint8_t LINE_RIGHT = 3;
const uint8_t SEG_CLK = 4;
const uint8_t SEG_DIO = 5;
const uint8_t RELAY_PIN = 6;
const uint8_t BUZZER_PIN = 7;
const uint8_t BUTTON_PIN = 8;
TM1637Display seg(SEG_CLK, SEG_DIO);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
const int TARGET = 25; // sticks per bundle per batch
int count = 0;
bool running = false, wasBlocked = false;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(LINE_LEFT, INPUT);
pinMode(LINE_RIGHT, INPUT);
seg.setBrightness(5);
seg.clear();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
seg.showNumberDec(0);
setRelay(false);
setBuzzer(false);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) { // start a new batch
count = 0; running = true; seg.showNumberDec(0); Serial.println(F("Batch started")); delay(400);
}
bool blocked = digitalRead(LINE_LEFT) == LOW; // an item over the sensor
if (running && blocked && !wasBlocked) {
count++; seg.showNumberDec(count); Serial.println(count);
if (count >= TARGET) {
running = false; Serial.println(F("Batch complete"));
for (int i = 0; i < 3; i++) { setBuzzer(true); delay(150); setBuzzer(false); delay(150); }
}
delay(30);
}
wasBlocked = blocked;
setRelay(running); // conveyor or feeder runs only during a batch
delay(5);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Lower the sensor to 5–10 mm from the surface and re-tune the trimmer until its LED switches between the light and dark surface.
CLK and DIO swapped; swap them.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, TCRT5000 Dual Channel Line Tracking Sensor Module, TM1637 4-Digit 7-Segment Display Module, 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, Tactile Push Button Switch, BO DC Gear Motor 3–12V, DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (agarbatti_bundle_counter.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹769 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Infrared reflectance sensing; Isolation, relays and switching higher-power loads; Multiplexed 7-segment displays; Pull-ups and debouncing.
Ideas that reuse this build: Conveyor batch counter and Seed packet counter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.