Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe joystick gives two numbers, one for each axis. The sketch nudges each servo a little while the stick is pushed, so the mount moves smoothly and stays where you leave it. Press the stick to re-centre.
Do not mount a laser pointer on the tilt servo unless an adult supervises the build.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Two potentiometers at right angles plus a push switch: it reports where the stick is, from -100 to 100 on each axis.
Moves the pan axis of the bracket.; Moves the tilt axis of the bracket.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_joystick_pan_tilt.inoVerify & upload in Electrolark// Joystick pan-tilt camera mount
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-joystick-pan-tilt"
#include <Servo.h>
// ---- pins ----
const uint8_t JOY_X = A0;
const uint8_t JOY_Y = A1;
const uint8_t JOY_BTN = 2;
const uint8_t SERVO_PAN = 3;
const uint8_t SERVO_TILT = 5;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int joyX = 0;
int joyY = 0;
Servo panServo, tiltServo;
const int DEAD_ZONE = 12; // ignore small values near the centre
int panAngle = 90, tiltAngle = 90;
unsigned long lastMove = 0;
void setup() {
Serial.begin(115200);
pinMode(JOY_BTN, INPUT_PULLUP);
panServo.attach(SERVO_PAN);
tiltServo.attach(SERVO_TILT);
panServo.write(panAngle);
tiltServo.write(tiltAngle);
}
void loop() {
if (millis() - lastMove < 20) return; // move every 20 ms
lastMove = millis();
int jx = map(analogRead(JOY_X), 0, ADC_MAX, -100, 100);
int jy = map(analogRead(JOY_Y), 0, ADC_MAX, -100, 100);
if (abs(jx) > DEAD_ZONE) panAngle = constrain(panAngle + jx / 25, 0, 180);
if (abs(jy) > DEAD_ZONE) tiltAngle = constrain(tiltAngle - jy / 25, 20, 160);
if (digitalRead(JOY_BTN) == LOW) { panAngle = 90; tiltAngle = 90; } // press the stick to centre
panServo.write(panAngle);
tiltServo.write(tiltAngle);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
This is normal. The sketch ignores small values near the centre (the dead zone).
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, PS2 Thumb Joystick Module (KY-023 style), 2 × TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (atl_joystick_pan_tilt.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹570 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog joysticks; PWM pulses and servo control.
Do not mount a laser pointer on the tilt servo unless an adult supervises the build.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.