Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe 28BYJ-48 stepper winds a cord loop that pulls the curtain. When the light sensor has seen daylight for a full minute the curtain opens; a minute of darkness closes it. The button toggles manual mode for lie-ins.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Small geared stepper motor (2048 steps per turn) with its ULN2003 driver board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
automatic_curtain_opener.inoVerify & upload in Electrolark// Automatic curtain opener
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "automatic-curtain-opener"
#include <Stepper.h>
// ---- pins ----
const uint8_t LDR_PIN = 2;
const uint8_t ST_IN1 = 3;
const uint8_t ST_IN2 = 4;
const uint8_t ST_IN3 = 5;
const uint8_t ST_IN4 = 6;
const uint8_t BUTTON_PIN = 7;
const int STEPS_PER_REV = 2048; // 28BYJ-48 in full-step mode
Stepper stepper(STEPS_PER_REV, ST_IN1, ST_IN3, ST_IN2, ST_IN4); // note the 1-3-2-4 order
// ---- latest readings ----
bool dark = false;
const long TRAVEL_STEPS = 4096; // two full turns of the 28BYJ-48; change for your curtain
bool open = false, manualOverride = false;
unsigned long darkSince = 0, lightSince = 0;
void moveTo(bool wantOpen) {
if (wantOpen == open) return;
Serial.println(wantOpen ? F("Opening") : F("Closing"));
stepper.step(wantOpen ? TRAVEL_STEPS : -TRAVEL_STEPS);
open = wantOpen;
digitalWrite(ST_IN1, LOW); digitalWrite(ST_IN2, LOW); digitalWrite(ST_IN3, LOW); digitalWrite(ST_IN4, LOW); // let the coils cool
}
void setup() {
Serial.begin(115200);
pinMode(LDR_PIN, INPUT);
stepper.setSpeed(10); // rpm (max about 15)
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) { manualOverride = !manualOverride; moveTo(!open); delay(500); }
if (manualOverride) return;
dark = digitalRead(LDR_PIN) == HIGH;
if (dark) { lightSince = 0; if (!darkSince) darkSince = millis(); } else { darkSince = 0; if (!lightSince) lightSince = millis(); }
if (darkSince && millis() - darkSince > 60000UL) moveTo(false); // dark for a full minute: close
if (lightSince && millis() - lightSince > 60000UL) moveTo(true);
delay(200);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Some modules invert DO. Change == HIGH to == LOW in the code.
Pin order is wrong: it must be IN1, IN3, IN2, IN4 in the Stepper constructor. Keep speed under 15 rpm.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital LDR Light Sensor Module – LM393, 28BYJ-48 Stepper Motor & ULN2003 Driver Kit, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (automatic_curtain_opener.ino). Install this library first: Stepper.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹495 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pull-ups and debouncing; Stepper motors and step sequences; Thresholds set in hardware vs software.
Ideas that reuse this build: Photo turntable and Night light. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.