555 timer LED flasher
The most famous chip in electronics, blinking an LED about once a second.
Shop by category
Shop all componentsA 1000 µF capacitor charges from the Nano 5 V through a 10 kΩ resistor, and the analog input reads the capacitor voltage ten times a second. The curve rises fast and then levels off: after one time constant (R × C = 10 seconds) it reaches about 63 % of 5 V. Short the capacitor with a wire to start again.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
For very small voltages (a fruit cell, one AA): the analog pin reads the cell directly through a 100 kΩ protection resistor.; 10 kΩ charging resistor
Follow the colours: red is power, dark grey is ground, blue is a signal.
Wire 5V → 10 kΩ → capacitor + → capacitor − to GND, and connect the capacitor + to the analog input through the 100 kΩ resistor. Observe the capacitor polarity.
class_capacitor_charging.inoVerify & upload in Electrolark// Watch a capacitor charge
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-capacitor-charging"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t VBAT_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float batteryV = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX; } // direct, 0 to the board voltage
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Capacitor"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Voltage"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(batteryV, 2);
oled.print(F(" V"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
batteryV = readBatteryV();
Serial.print(F("Voltage="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
A fruit cell has a high internal resistance: add a 100 nF capacitor from the pin to GND to steady it.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Students time how long it takes to reach 3.2 V, then predict the time for 2200 µF or 22 kΩ before testing. Use the Serial Plotter to draw the curve.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
6 parts: Nano CH340 Development Board (Soldered), Resistor Assortment Kit (30 Values), 0.96" OLED Display 128x64 (I2C), Electrolytic Capacitor, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_capacitor_charging.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹468 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Capacitors; Time constant.
Ideas that reuse this build: 555 LED flasher and Voltage divider lab. They are listed under Take it further on this page.
The most famous chip in electronics, blinking an LED about once a second.
Press once and the light stays on for about 11 seconds, then goes off by itself.
A running light like the one on Knight Rider, made from two classic chips.
Touch two wires with a fingertip and an LED lights: skin current switches a transistor pair.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Voltage=1.50V Voltage=1.51V Voltage=1.50V Voltage=1.51V Voltage=1.51V Voltage=1.50V Voltage=1.50V Voltage=1.50V Voltage=1.50V
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.